Related Manuals for Mea SMARTPACK 180-H
Summary of Contents for Mea SMARTPACK 180-H
- Page 1 SMARTPACK 180-H (7232) Owners & Operators Manual SERVICE MAINTENANCE AIR COMPRESSOR – HYDRAULIC DRIVEN 7232-D0001-01...
- Page 2 Document No 7232-D0001-01...
- Page 3 MEA Product Warranty Registration Form THIS FORM MUST BE COMPLETED AND RETURNED WITHIN 30 DAYS OF INSTALLATION WARRANTY WILL BE VOID Document No 7232-D0001-01...
- Page 4 CUT HERE MEA Product Warranty Registration Form This form must be completed and returned to MEA at the time of Installation. Warranty will be void if this form is not received by MEA within 30 days of installation. MEA Dealer Information...
-
Page 5: Table Of Contents
DRAWINGS & ILLUSTRATIONS ..................... 18 WARRANTY ............................26 Both the MEA Product Warranty Registration form (located at the FRONT of this Manual) and the Kohler Engine Warranty Registration form (located at the back of this manual) are to be returned to MEA. -
Page 6: Product Safety
PRODUCT SAFETY (COMPRESSOR / COMPRESSED AIR) MEA DISCLAIMS ANY AND ALL LIABILITIES FOR DAMAGE OR LOSS DUE TO PERSONAL INJURIES, INCLUDING DEATH, AND/OR PROPERTY DAMAGE INCLUDING CONSEQUENTIAL DAMAGES ARISING OUT OF ANY MEA SYSTEM NOT USED IN ACCORDANCE WITH THE OPERATOR INSTRUCTIONS. -
Page 7: Product Safety
PRODUCT SAFETY HYDRAULIC SAFETY ALL HYDRAULIC EQUIPMENT MUST BE TREATED WITH EXTREME RESPECT AND CARE. AS THE WORKING FLUID IS UNDER EXTREME PRESSURE, UP TO 5000PSI, WITH HIGH FLOW RATES GENERATING HIGH HEAT, ALL APPROPRIATE SAFETY PRECAUTIONS MUST BE TAKEN IN TO ACCOUNT AND SAFETY EQUIPMENT MUST BE WORN IF IN CONTACT WITH THE EQUIPMENT UNDER OPERATION. -
Page 8: Introduction
INTRODUCTION This MEA vehicle mounted air compressor system utilizes the vehicles engine to power the installed compressor to supply compressed air at the specified flow rate and pressure. Only those who have been trained and delegated to do so, and who have read and understand the operation and installation procedures should install MEA compressor systems. -
Page 9: Specifications
Safety Features: 200 PSI relief valve in compressor sump Temperature safety sensor in compressor Rapid blow-down valve to discharge system pressure on shutdown Lubrication: MEA Certified and Approved Oil Filters: Paper-type replaceable air filter Spin-on type oil filter Coalescing separator element... -
Page 10: Operating Procedure
OPERATING PROCEDURE WARNING CAREFULLY READ THE OPERATING INSTRUCTIONS BELOW. FAILURE TO ADHERE TO THE FOLLOWING COMPRESSOR OPERATING INSTRUCTION COULD RESULT IN SERIOUS INJURY. 1. Check Oil Level. 2. Check Hoses and fittings for leaks. 3. Check Loose/damaged hoses. 4. Check Air Filter for Blockage. 5. -
Page 11: Installation
When setting up the Compressor unit, ensure there is a safety mechanism in place to prevent any excessive flow or pressure into the compressor hydraulic circuit. MEA will not warrant any damage caused to the compressor from the existing hydraulic system. - Page 12 Document No 7232-D0001-01...
-
Page 13: Compressor Information
COMPRESSOR INFORMATION Document No 7232-D0001-01... - Page 14 Document No 7232-D0001-01...
- Page 15 Document No 7232-D0001-01...
- Page 16 Document No 7232-D0001-01...
- Page 17 Document No 7232-D0001-01...
- Page 18 Document No 7232-D0001-01...
- Page 19 Document No 7232-D0001-01...
- Page 20 Document No 7232-D0001-01...
- Page 21 SPARE PARTS Part Number Description 10008-P0024 AIR FILTER ELEMENT 10008-P0029 SPIN ON COALESCER 10008-P0078 OIL FILTER IMPORTANT: PLEASE CONTACT MOBILE ENERGY AUSTRALIA FOR MORE INFORMATION IF YOU HAVE ANY QUESTIONS REGARDING THE SETUP AND OPERATION OF THE SMARTPACK RANGE OF PRODUCTS.
-
Page 22: Drawings & Illustrations
DRAWINGS & ILLUSTRATIONS HARNESS SMARTPACK 180H FRAMED 12V AND 24V Document No 7232-D0001-01... - Page 23 HARNESS SMARTPACK 180H FRAMELESS 12V AND 24V Document No 7232-D0001-01...
- Page 24 C) SMARTPACK -H Compressor Remote Electronic Control Wiring 12 or 24V Document No 7232-D0001-01...
- Page 25 Document No 7232-D0001-01...
- Page 26 D) SMARTPACK -180H - GENERAL DRAWINGS Document No 7232-D0001-01...
- Page 27 Document No 7232-D0001-01...
- Page 28 E) SMARTPACK -180H - MOUNTING DRAWINGS Document No 7232-D0001-01...
- Page 29 F) SMARTPACK -180H HYDRAULIC CIRCUIT Document No 7232-D0001-01...
-
Page 30: Warranty
Components supplied under warranty shall be warranted for the remainder of the original warranty period. MEA factory rebuilt components shall be warranted for a period of 6 months from date of shipment. MEA OBLIGATIONS The obligation of MEA is limited to repairing or replacing parts, during normal business hours, at an authorized service facility, any component, that in the judgment of MEA are defective. - Page 31 A registration form is provided to the Buyer with the product(s). The form must be fully completed by the Buyer and returned to MEA upon completion of the installation of the product(s) in order to validate the warranty. No warranty claims will be processed unless MEA has received a fully completed warranty registration form.
- Page 32 MOBILE ENERGY AUSTRALIA - CONTACTS Management Managing Director – Rob Pulz Office: 07 3273 6803 Sales Email: sales@mobileenergyaustralia.com.au Office: 07 3273 6803 Spare Parts BH Office: 07 3273 6803 Email: spareparts@mobileenergyaustralia.com.au Service Email: workshop@mobileenergyaustralia.com.au Office: 07 3273 6803 Document No 7232-D0001-01...
Need help?
Do you have a question about the SMARTPACK 180-H and is the answer not in the manual?
Questions and answers