Summary of Contents for Igloohome Smart Deadbolt 2S IGB4
Page 1
Igloohome Smart Deadbolt 2S Model No.: IGB4 1. Dimensions and weight Front ‐ Height 144.5 mm Front ‐ Width 60 mm Front ‐ Thickness 13 mm (11 mm without rubber) Back ‐ Height 160mm Back ‐ Width 64.5mm Back ‐ Thickness 52mm Gross 1.64 kg Net 1.28 kg 2. Overall Design Front: ...
Page 2
3. Door Compatibility Door thickness If 60mm door thickness, no need to cut tailpiece range is 35mm to during installation. 60mm If 55mm door thickness, cut 1 notch of tailpiece. If 50mm door thickness, cut 2 notch of tailpiece. If 45mm door thickness, cut 3 notch of tailpiece. If 40mm door thickness, cut 4 notch of tailpiece. If 35mm door thickness, cut 5 notch of tailpiece. When standing in front of the door: If the door lock in front of you is at the RIGHT, it is a LEFT HANDED DOOR. If the door lock in front of you is at the LEFT, it is a RIGHT HANDED DOOR. Note that the LH/RH orientation does not depend on the bolt coming out direction. 4. Material: Body: Zinc Alloy Battery Compartment: ABS Faceplate: Acrylic 5. Environmental and Reliability Operating Temperature: ‐25 to 55 Degree Celsius Storage Temperature: ‐40 to 70 Degree Celsius ...
Page 3
6. Battery Life Battery used: 4 x AA Up to 1 year 7. Buttons and LED 12 Buttons (4 x 3) Keypad LED UNLOCK Icon 8. Audio and LED indications Digit 1 short Beep Unlock icon 1 short Beep Clear icon 2 short beeps Bluetooth connection UNLOCK icon flashes BLUE Successfully unlocked A‐B‐C‐D beeps after unlocked Successfully locked 1 long beep after locked Incorrect PIN 4 short beeps Reached max no of digits (16) 4 short beeps Keypad Disabled Mode activated Very Long beep Keypad Disabled Mode 2 short beeps deactivated Keypad Security Lockout Alarm low‐high siren ...
Page 4
Product will allow up to 8 masking pins before the actual PIN code (8 digits). Product will allow up to 9 masking pins before the actual PIN code (7 digits). Product will allow up to 10 masking pins before the actual PIN code (6 digits). Product will allow up to 11 masking pins before the actual PIN code (5 digits). Product will allow up to 12 masking pins before the actual PIN code (4 digits). 10. Emergency Jumpstart If internal batteries are fully drained or low Battery, user can use a 9V Battery to stay in contact to 2 conical contact pins (about 12mm apart) to jumpstart the product. When that 9V battery contacts with the 9V contact, there will be one single beep and keypad lights up for user to use any entry methods to unlock the product. 11. Tamper Alarm If the main cable between the front panel and back panel is disconnected, it will trigger the tamper alarm. If the cable is connected back, it will recover. 12. Manual Relock Hold on UNLOCK Button for one second to manual relock Can turn thumbturn or use physical key to physically relock 13. Auto Relock ...
Page 5
Unpaired product can be unlocked with Factory Pin code of 1234567890 (to test all buttons) followed by the Unlock Icon. 16. Connectivity Bluetooth 4.2 – Bluetooth Low Energy (BLE) 17. Volume Control Volume can be changed via Bluetooth 10 levels 18. Keypad Security Lockout Security Lockout will be triggered if Incorrect pins are attempted for a number of consecutive times. Keypad Security Lockout can be activated regardless of the lock status. User is able to Enable and disable Security Lockout via BT User is able to configure 1 to 10 incorrect pins (default = 5) When “Security Lockout” is triggered 1st time: There will be siren for 30 seconds Keypad will not accept any pin codes for 1 minute When “Security Lockout ” is consecutively triggered 2nd time: There will be siren for 60 seconds Keypad will not accept any pin codes for 5 minutes When “Security Lockout” is consecutively triggered 3rd and subsequent times: ...
Page 6
19. Keypad Disabled Mode Keypad Disabled Mode can be activated by pressing the Function button for 3 seconds and keypad will not accept any pin codes. Keypad Disabled Mode can be activated regardless of the lock status. When “Keypad Disabled Mode” is activated, there will be a clear audio indicator. During Keypad Disabled Mode, double Flash White LED when keypad is triggered. When “Keypad Disabled Mode” is activated, Auto Relock will not function to eliminate the case where user will get locked out if auto relock is allowed. Keypad Disabled Mode can be deactivated by: Holding on to Function button for 2 seconds Any Bluetooth Unlock Unlock by Physical Key Unlock by Thumbturn 20. Passage Mode When the lock is unlocked, Hold the Function button for 3 seconds to activate Passage mode. When passage mode is activated, lock will not relock when door is closed and keypad is disabled. 21. Access requirements Master BT Key Guest BT Key Master PIN Permanent PIN ...
Page 7
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.