Advertisement
Samba™ OPLC™
SM35-J-R20/SM43-J-R20
SM70-J-R20
SM35-J-T20/SM43-J-T20
SM70-J-T20
General Description
All of the controllers covered in this guide are micro-OPLCs, rugged programmable logic controllers
that comprise built-in operating panels and on-board I/Os.
Item
On-board I/O
Screen
Keypad or
Function Keys
Programming Com
Port, Built-in
RS232
USB device,
mini-B
Com Ports,
separate order,
user-installed
Standard Kit Contents
Item
Controller
Terminal Blocks
Battery
Mounting Brackets
Rubber Seal
Unitronics
OPLC Installation Guide
12 Digital Inputs, include 1 HSC/Shaft-encoder Input,
2 Analog inputs (only when the digital inputs are set to pnp)
8 Relay Outputs
12 Digital Inputs, include 3 HSC/Shaft-encoder Input,
2 Analog inputs
8 Transistor Outputs
SM35-J-R20
SM35-J-T20
3.5" Color Touch
Yes
None
The user may install a CANbus module (V100-17-CAN), and one of the following:
RS232/RS485 port (V100-17-RS4/V100-17-RS4X)
•
Ethernet (V100-17-ET2)
•
SM35-J-R20
SM35-J-T20
Yes (installed)
Yes (2 parts)
SM43-J-R20
SM43-J-T20
Model Dependent
4.3" Color Touch
None
None
Yes
SM43-J-R20
SM43-J-T20
Yes
Yes
Yes (installed)
Yes (4 parts)
Yes
SM70-J-R20
SM70-J-T20
7" Color Touch
None
Yes
SM70-J-R20
SM70-J-T20
Yes
Yes (6 parts)
1
Advertisement
Table of Contents
Related Manuals for Unitronics Samba OPLC Series
Summary of Contents for Unitronics Samba OPLC Series
- Page 1 RS232/RS485 port (V100-17-RS4/V100-17-RS4X) • user-installed Ethernet (V100-17-ET2) • Standard Kit Contents SM35-J-R20 SM43-J-R20 SM70-J-R20 Item SM35-J-T20 SM43-J-T20 SM70-J-T20 Controller Terminal Blocks Battery Yes (installed) Yes (installed) Mounting Brackets Yes (2 parts) Yes (4 parts) Yes (6 parts) Rubber Seal Unitronics...
-
Page 2: Alert Symbols And General Restrictions
All examples and diagrams are intended to aid understanding, and do not guarantee operation. Unitronics accepts no responsibility for actual use of this product based on these examples. Please dispose of this product according to local and national standards and regulations. - Page 3 Samba™ OPLC™ Mounting Dimensions SM35-J-R20/SM35-J-T20 SM43-J-R20/SM43-J-T20 SM70-J-R20/SM70-J-T20 Unitronics...
-
Page 4: Panel Mounting
4. Tighten the bracket’s screws against the panel. Hold the bracket securely against the unit while tightening the screw. 5. When properly mounted, the controller is squarely situated in the panel cut-out as shown in the accompanying figures. SM35 SM43 Unitronics... -
Page 5: Wiring Procedure
Input or output cables should not be run through the same multi-core cable or share the same wire. Allow for voltage drop and noise interference with I/O lines used over an extended distance. Use wire that is properly sized for the load. The controller and I/O signals must be connected to the same 0V signal. Unitronics... - Page 6 Set to JP12 (all Inputs) npn (sink) pnp (source)* Input 5: Set Type - Digital or Analog #1 Set to JP10 Digital* Voltage Current Input 6: Set Type - Digital or Analog #0 Set to Digital* Voltage Current *Default settings Unitronics...
- Page 7 JP5 (Input 10) JP6 (Input 11) Digital* Analog Analog Inputs AN0/AN1: Set Type Set to JP3 (AN0) JP4 (AN1) Voltage* Current *Default settings I/O Wiring npn Input Wiring SM35/43/70-J-R20 SM35/43/70-J-T20 Input wiring, npn (sink) HSC input wiring, npn (sink) Unitronics...
- Page 8 Samba™ OPLC™ Installation Guide pnp Input Wiring SM35/43/70-J-R20 SM35/43/70-J-T20 Input wiring, pnp (source) HSC input wiring, pnp (source) Shaft-encoder SM35/43/70-J-R20 SM35/43/70-J-T20 Unitronics...
- Page 9 To increase the life span of the relay output contacts and protect the device from potential damage by reverse EMF, connect: A clamping diode in parallel with each inductive DC load An RC snubber circuit in parallel with each inductive AC load Unitronics...
-
Page 10: Power Supply
This series comprises a USB port. The USB port in SM43 Series is not isolated. Make sure that the PC and the controller Caution are grounded to same potential. The USB port may be used for programming, OS download and PC access. Unitronics... - Page 11 Note: Photo is for illustration purposes only. (Using SM70) Closing the Controller Replace the back cover of the controller and fasten the corner screws. Note that you must replace the back cover securely before powering up the controller. Unitronics...
- Page 12 Samba™ OPLC™ Installation Guide FINLAND RUSSIA BELARUS KAZAKHSTAN info@klinkmann.fi klinkmann@klinkmann.ru minsk@klinkmann.com klinkmann@klinkmann.kz www.klinkmann.fi www.klinkmann.ru www.klinkmann.by www.klinkmann.kz ESTONIA LATVIA LITHUANIA UKRAINE info@klinkmann.ee info@klinkmann.lv info@klinkmann.lt klinkmann@klinkmann.kiev.ua www.klinkmann.ee www.klinkmann.lv www.klinkmann.lt www.klinkmann.com.ua...