Download Print this page

Cisco Card Cage and Backplane 7513-MX Replacement Instructions Manual

Cisco systems bridge/router replacement instructions
Hide thumbs

Advertisement

Quick Links

Text Part Number: 78-1895-04
Customer Order Number: DOC-781895=
Cisco 7513, Cisco 7513-MX, and
Cisco 7576 Card Cage and Backplane
Assembly Replacement Instructions
Product Numbers: MAS-7513CDCAGE= (Cisco 7513), MAS-7513MX-CDCAGE=
(Cisco 7513-MX), MAS-7576CDCAGE= (Cisco 7576)
This publication provides the procedures to replace the card cage and backplane assembly in the
Cisco 7513, Cisco 7513-MX, and Cisco 7576 routers. The card cage and backplane assembly for the
Cisco 7513, Cisco 7513-MX, and Cisco 7576 chassis can be replaced in the field. The assembly is a
single field-replaceable unit (FRU) that requires replacement by a Cisco-certified service provider
only.
This publication assumes you have already performed troubleshooting on your chassis and system
and determined that this replacement is required.
Document Contents
This publication includes the following sections:
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Copyright © 1999
Cisco Systems, Inc.
All rights reserved.
1

Advertisement

loading

  Also See for Cisco Card Cage and Backplane Cisco 7513-MX

  Related Manuals for Cisco Card Cage and Backplane Cisco 7513-MX

  Summary of Contents for Cisco Card Cage and Backplane Cisco 7513-MX

  • Page 1: Table Of Contents

    Checking the System, page 21 • Port and Slot Configuration Worksheet, page 23 • Cisco Connection Online, page 25 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 Copyright © 1999 Cisco Systems, Inc. All rights reserved.
  • Page 2: Product Overview

    Product Overview Before replacing the card cage and backplane assembly, read the “Safety Guidelines” Caution section on page 7. The specific procedures for removing and installing the card cage and backplane assembly might require two people to perform. Product Overview The Cisco 7513, Cisco 7513-MX, and Cisco 7576 card cage holds the processor modules used by the system.
  • Page 3 Figure 1 Cisco 7513, Cisco 7513-MX, and Cisco 7576—Rear-Panel View Blower module Cable-management bracket Card cage and processor modules Interface processor slot numbering scheme Air intake vent Power supplies POW ER Chassis grounding receptacles The Cisco 7513, Cisco 7513-MX, and Cisco 7576 use the same chassis, power supplies, Note accessories, and slot numbering scheme.
  • Page 4 Product Overview To provide a viewable image, slot numbers 0, 1, 2, 11, and 12 are not shown in Figure 2. The Note slot numbering scheme uses color coding to assist in identifying routers and CyBus assignments. Refer to the “Identifying Cisco 7576 Independent Routers and CyBuses” section in the Cisco 7500 Series Installation and Configuration Guide for detailed information on the slot numbering scheme.
  • Page 5: Installation Safety, Esd Precautions, And Tools Required

    Figure 4 shows the location of the Cisco 7576 dual arbiters and chassis interfaces on the rear of the backplane. Figure 4 Dual arbiters Chassis interfaces When you view the rear of the card cage, the dual arbiter and chassis interface on the right Note side are used with router A, and the dual arbiter and chassis interface on the left side are used with router B.
  • Page 6: Safety Warnings

    Installation Safety, ESD Precautions, and Tools Required Safety Warnings Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement. This warning symbol means danger. You are in a situation that could cause bodily Warning injury.
  • Page 7: Safety Guidelines

    Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos Aviso físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes.
  • Page 8: Tools Required

    Installation Safety, ESD Precautions, and Tools Required In addition, use the guidelines that follow when working with any equipment that is connected to telephone wiring or other network cabling: • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
  • Page 9: Removing And Replacing Processor Modules

    Removing and Replacing Processor Modules Before you can replace the card cage and backplane assembly, you need to remove all processor modules installed in the card cage, and then replace them after the new card cage assembly is in place. The term processor module refers to the RSP2, RSP4, or RSP8 and all interface processors. Note Always use the ejector levers when installing or removing processor modules.
  • Page 10 Removing and Replacing Processor Modules Figure 5 Captive installation screw 10 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Ejector Levers and Captive Installation Screws Bottom ejector lever Processor module carrier guide Stop immediately on contact Processor module slot...
  • Page 11 Figure 6 Caution To prevent damage to the processor modules, do not stack them on top of each other. Replacing Processor Modules You can replace an interface processor in any of the 11 interface processor slots, 0 through 5, and 8 through 12, from left to right.
  • Page 12: Removing Power Supplies

    Removing Power Supplies Always install blank processor module fillers in empty processor slots to maintain the Caution proper flow of cooling air through the chassis. Use a screwdriver to tighten both captive installation screws on each processor module. Step 7 Attach network interface cables or other devices to the interface ports.
  • Page 13 Disconnect the power supply cables from the power supplies. Step 2 • For DC-input power supplies, refer to the configuration note 1200-Watt DC-Input Power Supply Replacement Instructions (Publication Number 78-1899-xx) that shipped with your Cisco 7513, Cisco 7513-MX, or Cisco 7576 chassis equipped with DC-input power supplies.
  • Page 14: Removing The Old Card Cage And Backplane Assembly

    Removing the Old Card Cage and Backplane Assembly To maintain agency compliance requirements and meet electromagnetic interference Caution (EMI) emissions standards in a Cisco 7513 or Cisco 7576 chassis with a single power supply, the power supply blank must remain in the power supply bay adjacent to the power supply. (See Figure 10.) Replace this blank in the chassis after you replace the card cage assembly.
  • Page 15 To remove the card cage and backplane assembly, follow these steps: Turn the power switch on each power supply to the off position (O). Step 1 Step 2 Disconnect the power supplies. • For DC-input power supplies, refer to the configuration note 1200-Watt DC-Input Power Supply Replacement Instructions (Publication Number 78-1899-xx) that shipped with your Cisco 7513, Cisco 7513-MX, or Cisco 7576 chassis equipped with DC-input power supplies.
  • Page 16: Exchanging The Eeprom Devices

    Exchanging the EEPROM Devices Figure 11 Captive screw Card cage side flange Captive screw Air intake grill With the captive screws loosened, carefully pull the card cage and backplane assembly Step 6 straight out of the chassis until the entire assembly is clear of the chassis sides. (See Figure 11.) The assembly is not heavy but might be awkward to handle.
  • Page 17 The new EEPROM device(s) that shipped on your new card cage are blank. Caution Do not perform these steps if you are upgrading a Cisco 7513 to a Cisco 7576. These Note instructions apply only to the replacement of an equivalent card cage. The following procedure requires you to first exchange the blank EEPROM device(s) on your new card cage for the old EEPROM device(s) from your old card cage, and then place the blank EEPROM device(s) on your old card cage for return to Cisco.
  • Page 18: Installing The New Card Cage And Backplane Assembly

    Installing the New Card Cage and Backplane Assembly Figure 13 Chassis interface board B Note router A and router B. The backplane of the Cisco 7576 includes two dual arbiters, two chassis interfaces, and two EEPROM devices. Figure 13 shows the specific location and designation of each EEPROM device.
  • Page 19 Figure 14 Replacing the Card Cage and Backplane Assembly Captive screw Card cage side flange Captive screw Air intake grill POW ER Caution The electronic components on the rear of the backplane are completely exposed when the card cage and backplane assembly is removed from the chassis. To prevent damaging these components, carefully slide the assembly into the chassis opening.
  • Page 20: Replacing Power Supplies

    Replacing Power Supplies Replacing Power Supplies To replace the power supply, follow these steps: To replace a power supply, hold it as shown in Figure 15 and slide it into the power supply Step 1 bay. Push the supply all the way into the chassis until the sides are flush against the chassis frame.
  • Page 21: Checking The System

    Repeat Step 1 through Step 3 for the second power supply if one is installed, or Step 1 Step 4 and Step 2 for the power supply blank if one is present. Note supply, reconnect the power cable at the power source. This completes the power supply replacement procedure.
  • Page 22 Checking the System Following is an example of this display: (display text omitted) GS Software (RSP-K), Version 10.3(571) Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Wed 10-May-95 25:12 RSP2 (Risc 4600) processor with 16384K bytes of memory. (display text omitted)
  • Page 23: Port And Slot Configuration Worksheet

    Port and Slot Configuration Worksheet The port and slot configuration worksheet (Table 1) is used with Figure 17 to assist in planning and documenting your use of the slots in a Cisco 7513, Cisco 7513-MX, or Cisco 7576 router. Figure 17 depicts the dual CyBus backplane, minus the time division multiplexing (TDM) connectors found on the Cisco 7576.
  • Page 24 Port and Slot Configuration Worksheet Figure 17 Cisco 7513 and Cisco 7513-MX Slot Assignments The dual CyBus backplane has 13 slots: interface processors are placed in slots 0 through 5 and 8 through 12. RSPs are placed in slots 6 and 7. Cisco 7576 Slot Assignments The Cisco 7576 consists of two independent routers on a single backplane.
  • Page 25: Cisco Connection Online

    Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services. Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco’s customers and business partners.
  • Page 26 Wavelength Router Protocol, WebViewer, Workgroup Director, and Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, The Internet Economy, and The New Internet Economy are service marks; and ASIST, BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, the Cisco Systems Cisco Press logo, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastLink, FastPAD, FastSwitch, GeoTel, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc.

This manual is also suitable for:

Cisco7576Router cisco 7513