Download Print this page

Cisco 7513 Series Replacement Instructions Manual

Chassis replacement
Hide thumbs

Advertisement

Quick Links

Doc. No.
78-1897-01
Cisco 7513 Chassis Replacement Instructions
Product Numbers: CHAS-7513-DC=, CHAS-7513-AC=, and MAS-7513=
This document provides instructions for replacing the Cisco 7513 chassis, which is available as a
spare part.
Note
The chassis is available as a spare part, and includes all of the components required for operation
except the processor modules and power supplies (MAS-7513=), or as a spare with power supplies
(CHAS-7513-DC= or CHAS-7513-AC=).
After you replace the chassis, you must move the processor modules from your old chassis into your
new chassis.
The replacement chassis does not include the cable-management or rack-mounting hardware kits.
You can move the rack-mounting hardware and cable-management bracket from the existing chassis,
or order either kit as a spare part, which will ship with installation instructions.
The sections in this document include the following:
Copyright © 1995
Cisco Systems, Inc.
All rights reserved.
Through this document, the term the chassis is be used to refer to the Cisco 7513 chassis.
What Is the Cisco 7513?, page 2
Prerequisites, page 3
Replacing the Chassis, page 7
— Replacing a Rack-Mounted Chassis, page 8
— Installing the Cable-Management Bracket, page 12
— Moving Processor Modules from the Old Chassis to the New Chassis, page 13
— Checking the Installation, page 17
— Verifying the Installation Using show Command Descriptions and Examples, page 19
Cisco Information Online, page 22
1

Advertisement

loading

  Related Manuals for Cisco 7513 Series

  Summary of Contents for Cisco 7513 Series

  • Page 1 This document provides instructions for replacing the Cisco 7513 chassis, which is available as a spare part. Through this document, the term the chassis is be used to refer to the Cisco 7513 chassis. Note The chassis is available as a spare part, and includes all of the components required for operation except the processor modules and power supplies (MAS-7513=), or as a spare with power supplies (CHAS-7513-DC= or CHAS-7513-AC=).
  • Page 2 What Is the Cisco 7513? What Is the Cisco 7513? The Cisco 7513 is a 13-slot router chassis, which uses the RSP2 and CxBus and CyBus interface processors. The chassis provides up to eleven interface processor slots. Although the chassis uses two high-speed, 1.067-gigabit-per-second (Gbps) CyBuses, it can accommodate all CxBus-based...
  • Page 3: Safety Guidelines

    Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. Cisco 7513 Chassis Replacement Instructions...
  • Page 4 Avoid contact between the board and clothing. The ESD strap only protects the board from ESD voltages on the body; ESD voltages on clothing can still cause damage. Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohms. 4 Cisco 7513 Chassis Replacement Instructions...
  • Page 5: Cable Strain Relief

    When removing any cable, pull the cable out at the connector; never pull or tug on the cable itself. For detailed descriptions of the system components, refer to the Cisco 7513 Hardware Installation and Maintenance publication.
  • Page 6 Chassis Footprint and Clearance Requirements for Maintenance 19 inches required for blower removal 1.75 inches 4 places 3.94 inches 12.73 inches 1.47 Plastic front inches panel end 14.57 inches 18.93 17.50 inches inches 18.75 inches 21.23 inches 6 Cisco 7513 Chassis Replacement Instructions...
  • Page 7: Tools And Parts Required

    — 1/4-inch and 3/16-inch, flat-blade screwdrivers — the ACS-7000RMK(=) rack-mount kit (with hardware) for the chassis (this kit also works for the Cisco 7000 chassis) • Whenever you remove or install processor modules, have the following equipment on hand to help prevent ESD damage: —...
  • Page 8 Cisco 7513 Rack-Mount Kit Installation Instructions (Document Number 78-2023-xx). After you install the new chassis in the rack and install the cable-management brackets, proceed to the section “Moving Processor Modules from the Old Chassis to the New...
  • Page 9 Turn OFF the system power and disconnect the power cable and all interface cables from Step 1 the chassis. Step 2 Use a screwdriver to loosen and remove each of the four screws (two on each side) that secure the chassis ears to the rack rails. Cisco 7513 Chassis Replacement Instructions...
  • Page 10 Figure 4. Grasping the chassis as shown in Figure 4, slowly lift the chassis in unison. To prevent Step 2 injury, avoid sudden twists or moves. 10 Cisco 7513 Chassis Replacement Instructions...
  • Page 11 (See Figure 5.) Secure each ear to the rack-mounting post with two 10-32 x 5/8-inch, Phillips pan-head Step 5 screws. This completes the procedure for moving the chassis into the rack. Cisco 7513 Chassis Replacement Instructions...
  • Page 12: Installing The Cable-Management Bracket

    Also, do no block the power supply air vents with cables. This completes the procedure for installing the cable-management bracket. Proceed to the next section for the procedure for removing processor modules. 12 Cisco 7513 Chassis Replacement Instructions...
  • Page 13 Use the optional cable-management brackets to keep the interface cables untangled and away from other interface processor slots and ports. Cisco 7513 Chassis Replacement Instructions...
  • Page 14 files. Figure 7 Ejector Levers and Captive Installation Screws Bottom ejector lever Processor module Processor module slot carrier guide Captive installation screw STOP! on contact 14 Cisco 7513 Chassis Replacement Instructions...
  • Page 15 Do not use unnecessary force when installing processor modules. Always guide the carrier into the slot only until the carrier faceplate makes contact with the ejector levers; then use the ejector levers to complete the insertion. Cisco 7513 Chassis Replacement Instructions...
  • Page 16 This completes the processor module removal and replacement procedure. If you now need to install the new chassis in an equipment rack, proceed to the section “Installing the New Chassis in the Rack” on page 10. Otherwise, proceed to the next section to check the installation. 16 Cisco 7513 Chassis Replacement Instructions...
  • Page 17: Checking The Installation

    If, however, you installed interface processors in different slot positions in the new chassis, the system will recognize the interfaces, but will leave them in a down state until you reconfigure and enable them. If you need technical assistance, refer to the section “Cisco Information Online” at the end of this document. Step 1 Ensure that the system power switch is in the off position, then reconnect the power cable to the AC receptacle or DC terminal block, as required.
  • Page 18 Verify that the console terminal displays a script and system banner similar to the Step 9 following: GS Software (RSP-K), Version 10.3(571), SOFTWARE Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Wed 10-May-95 14:46 by mpo System Bootstrap, Version 4.6(1) [fc2], SOFTWARE Step 10...
  • Page 19 In the following example of the show version command, the system software is Release 10.3(571)). Router> show version GS Software (RSP-K), Version 10.3(571), SOFTWARE Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Wed 10-May-95 14:46 by mpo System Bootstrap, Version 4.6(1) [fc2], SOFTWARE Current date and time is Sat 1-22-1994 21:38:35...
  • Page 20 The command show protocols displays the global (system-wide) and interface-specific status of any configured Level 3 protocol. Router> show protocols Global values: Internet Protocol routing is enabled Hssi1/0 is up, line protocol is up (display text omitted) 20 Cisco 7513 Chassis Replacement Instructions...
  • Page 21 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 8 Slot 9 Slot 10 Slot 11 Slot 12 Router Name Location Serial Number 1. Slots 6 and 7 are reserved for the RSP2. Cisco 7513 Chassis Replacement Instructions...
  • Page 22: Cisco Information Online

    LAN/X.25, Point and Click Internetworking, SMARTnet, SynchroniCD, Packet, UniverCD, WNIC, Workgroup Director, Workgroup Stack, and XCI are trademarks; Access by Cisco and Bringing the power of internetworking to everyone are service marks; and Cisco, Cisco Systems, the Cisco logo, EtherSwitch, and Kalpana are registered trademarks of Cisco Systems, Inc. All other trademarks, service marks, registered trademarks, or registered service marks mentioned in this document are the property of their respective owners.

This manual is also suitable for:

Chas-7513-dc seriesChas-7513-ac seriesMas-7513 series