Download Print this page

Cisco 7507 Quick Start Manual

Cisco router quick start guide.
Hide thumbs

Advertisement

Is Cisco documentation helpful? Click
give us your feedback.
S
TART AND
I
NSTALL

Quick Start Guide

here
or go to http://www.cisco.com/warp/public/732/docsurvey/rtg/ to
C
7 5 0 7 R
I S C O
1
I
NSTALL THE
2
C
ONNECT THE
3
C
ONFIGURE THE
4
F
R
IELD
EPLACEABLE
5
O U T E R
N O R M A L
P O W E R
L O W E R
U P P E R
P O W E R
H
ARDWARE
RSP
S
YSTEM
U
(FRU
NITS
)
S

Advertisement

   Related Manuals for Cisco 7507

   Summary of Contents for Cisco 7507

  • Page 1: Quick Start Guide

    Is Cisco documentation helpful? Click give us your feedback. I S C O NSTALL THE TART AND NSTALL IELD Quick Start Guide here or go to http://www.cisco.com/warp/public/732/docsurvey/rtg/ to 7 5 0 7 R O U T E R N O R M A L L O W E R P O W E R P O W E R...

  • Page 3: Install The Hardware

    Lower power supply The Cisco 7507 has seven slots: slots 2 and 3 for the Route Switch Processors (RSPs), and slots 0, 1, 4, 5, and 6 for the interface processors. There are bays for up to two AC-input or DC-input power supplies.

  • Page 4

    Install the Hardware Prepare to Install the Router Note For detailed hardware installation instructions and safety guidelines, refer to the Cisco 7500 Series Router Installation and Configuration Guide, Site Preparation and Safety Guide, and the Cisco 7500 Regulatory Compliance and Safety Guide.

  • Page 5: Install The Router

    Install the Hardware Install the Router Note To rack-mount the router, refer to the “Rack-Mount the Router (Optional)” section on page 4. Caution Two people are required to perform this step. Avoid sudden twists or moves to prevent injury. Step 1 With a person positioned at either side of the chassis, grasp the bottom edge of the chassis with one hand near the front and...

  • Page 6

    Install the Hardware Rack-Mount the Router (Optional) M4 x 10-mm long Phillips flat-head screws (to attach To rack-mount a Cisco 7507 router, perform the following steps: Step 1 Mount the brackets to the rack posts. Step 2 Secure the spanner bars.

  • Page 7

    Install the Hardware Mount Brackets to the Rack Posts Note The distance between the inner edges of the left and right rack-mounting posts must be at least 17.72 inches (45.088 cm), and the distance between the holes in the mounting posts must be 18.31 inches (46.5 cm) (+ .063 inches or .16 cm).

  • Page 8

    Install the Hardware Secure the Spacers Step 1 Loosen the 10-32 x 5/8-inch LG Phillips pan-head screw at the end of the ledge of the right-side bracket. This screw is the anchor for the spanner bar. Step 2 Remove the tape that secures the spanner bar on the left bracket, and swing the bar down (see A) over the anchor screw on the opposite bracket.

  • Page 9

    Install the Hardware Attach the Chassis Ears Center-mount position Step 1 Position the ears on the chassis as follows: • To flush-mount the chassis, place each ear so that the mounting strips are flush with the end of the chassis, and align the mounting holes in the ear with those in the chassis.

  • Page 10

    Install the Hardware Mount the Chassis in the Rack Warning Two people are required to perform this step. Step 1 Slowly lift the chassis in unison. Lower it until it rests on the two ledges of the brackets. Step 2 Slide the chassis back into the rack along the ledges.

  • Page 11

    Install the Hardware Remove the Chassis Foot Flat-blade screwdriver slot for removing chassis foot Step 4 Turn the foot counterclockwise to loosen it until the foot drops out of the chassis. Step 5 Continue sliding the chassis into the rack until the ears meet the front mounting posts on both sides of the rack.

  • Page 12

    Install Interface Processors, Fillers, VIPs, or RSPs Card carrier guide (black) The Route Switch Processor (RSP) comes uninstalled with your Cisco 7507 router, but is a required system component. Install the RSPs in the slot 2 or slot 3, and install any interface processors, fillers, or Versatile Interface Processors (VIPs) in slots 0, 1, 4, 5, and 6 (optional).

  • Page 13

    Install the Hardware Install Power Supplies in the Router tive allation This procedure applies to AC-input and DC-input power supplies, with differences clearly noted. Do not mix AC-input and DC-input power supplies in the same chassis. Install the first power supply in the lower power supply bay and the second, if any, in the upper bay.

  • Page 14

    Step 5 Use a screwdriver to tighten the captive installation screw on the top of the power supply. Note For DC-input power supplies, refer to the “Install the DC-Input Power Supply” section on page 13 to complete this procedure. Step 6 Push the cable retention clip away from the power supply receptacle, and push the power cable in until the cable retention clip snaps into place.

  • Page 15

    Install the Hardware Install the DC-Input Power Supply Captive installation screws on terminal block cover DO NOT SHIP WITH POWER SUPPLY R TO BE FULLY ENGAGED INSTALLED OPERATING POWER SUPPLY INPUT VOLTAGE : 40-72 V= INPUT CURRENT : 24-13A allation screws l block cover FASTENER TO BE FULLY ENGAGED BEFORE OPERATING POWER SUPPLY...

  • Page 16

    Note Perform Step 1 through Step 5 on the previous page before following the steps below. Step 1 Using a screwdriver, loosen the captive installation screws on the terminal block cover. Step 2 Lift and remove the terminal block cover. Step 3 Wire the DC power supply using the appropriate lugs at the wiring end.

  • Page 17: Connect The Console Port

    Connect the RSP DB-25 female DB-25 male terminal Connect the Console Port The system console port on the RSP is a DB-25 receptacle DCE port for connecting a data terminal, which allows you to configure and manage the system. The console port is labeled Console. Step 1 Connect the console cable from the terminal to the console port on the RSP.

  • Page 18

    RSP2s, RSP4s, or RSP8s, to a single console terminal, or external auxiliary device. These are configured as system master and slave in slots 2 and 3 in the Cisco 7507. Step 1 Connect the DB-25 female end of the Y-cable to the console terminal device.

  • Page 19

    GS Software (RSP-K ), Version 11.1(8)CA Copyright (c) 1986-1995 by Cisco Systems, Inc. This RSP2 is system master Other RSP2 is not plugged in Compiled Wed 10-May-95 11:06 Step 7 Observe the system startup banner.

  • Page 20

    Start and Configure the System Start a Basic Configuration Many privileged-level EXEC commands are used to set operating parameters. To enter the privileged-level: Step 1 Enter the enable command at the EXEC prompt (>), and then enter a privileged-level password, as follows: Router>...

  • Page 21

    Start and Configure the System Perform a Basic Configuration Using Setup Note The router’s serial (WAN) cable should not be connected to the CSU/DSU unless you are planning to use AutoInstall. If you are using the console Y-cable that shipped with your router, use either of the two DB-25 male plug ends of the Y-cable.

  • Page 22

    Step 7 Enter yes or press Return to configure IP, and then select an interior routing protocol for IP, if you are using IP routing: Configure IP? [yes]: yes Configure IGRP routing? [yes]: yes Your IGRP autonomous system number [1]: 15 Step 8 At the # prompt, enter the copy running-config startup-config command...

  • Page 23

    Start and Configure the System Configure an Ethernet Interface Step 1 To configure your system for an Ethernet LAN, respond to the prompts as follows, using your own IP address and subnet mask information: Configuring interface parameters: Configuring interface Ethernet0/0: Is this interface in use? [no]: yes Configure IP on this interface? [no]: yes IP address for this interface: 1.1.1.10...

  • Page 24

    At the # prompt, enter the copy running-config startup-config command to save the configuration to NVRAM as follows: Hostname# copy running-config startup-config Your Cisco 7507 router is now minimally configured and ready to use. If you want to modify the parameters after the initial configuration, use the setup command.

  • Page 25

    NVRAM as follows: Hostname# copy running-config startup-config Your Cisco 7507 router is now minimally configured and ready to use. If you want to modify the parameters after the initial configuration, use the setup command. To perform more complex configurations, use the configure command.

  • Page 26: Flash Memory Cards

    Install Field Replaceable Units (FRUs) Flash Memory Cards A Flash memory card that ships with your Cisco 7507 contains the Cisco IOS software image to boot your router. You do not need to format it.

  • Page 27

    The RSP has two PC Card slots—slot 0 and slot 1—into which you can install a Flash memory card. In the RSP2, RSP4, and RSP8, the orientation is vertical. PC Card slot 0 is on the left and slot 1 is on the right (as shown). Note A Flash memory card can be inserted and removed with the system power on.

  • Page 28

    Install Field Replaceable Units (FRUs) Format a Flash Memory Card Flash memory cards shipped as spare parts must be formatted. Use only Intel Series 2+ Flash memory cards. Step 1 Enter format slot0: (or format slot1:) to format the Flash memory card, as follows: Router# format slot0: Step 2 At the erase all sectors prompt, press...

  • Page 29

    Install Field Replaceable Units (FRUs) Make a Flash Memory Card Image Bootable Note In this example, the filename is new.image, and the Flash memory card is located in slot 0. Step 1 Enter the configure terminal command at the enable prompt, as follows: Router# configure terminal Step 2 Enter the no boot system command, as...

  • Page 30

    Install Field Replaceable Units (FRUs) Prepare to Remove and Install an RSP To remove and install an RSP, you will perform the following steps: • Copy the configuration file using a Trivial File Transfer Protocol (TFTP) server • Remove the RSP •...

  • Page 31

    Install Field Replaceable Units (FRUs) Remove and Install an Interface Processor, Filler, VIP, or RSP Bottom ejector lever Card Card carrier slot Captive guide installation screw STOP! on contact Note Do not shut down the system power when removing an interface processor, VIP, or an RSP in a system configured for high availability HA.

  • Page 32

    Install Field Replaceable Units (FRUs) Step 8 If you have a VIP4 and are using HSA with an RSP2 as the slave processor, wait 20-30 seconds, then reinsert the RSP2. Step 9 Repeat Step 2 through Step 8 to remove any additional interface processors, fillers, VIPs, or RSPs.

  • Page 33

    Install Field Replaceable Units (FRUs) Check the Interface Processor or VIP Installation Note When a new VIP is inserted or when a VIP is moved to a new slot, the system recognizes the new interfaces, but leaves them in the shutdown state until you configure them.

  • Page 34

    Install Field Replaceable Units (FRUs) Copy the Configuration File for an RSP Refer to the appropriate Cisco IOS software documentation for the configuration options available, and for specific configuration instructions, as needed. Before you copy (save) the running configuration to a TFTP file server, ensure the following: •...

  • Page 35

    Step 6 Enter the name or IP address of the remote host. In the following example, the name of the remote server is servername: Router# copy startup-config tftp Remote host []? servername Translating "servername"...domain server (1.1.1.1) [OK]...

  • Page 36

    Install Field Replaceable Units (FRUs) Step 7 Enter the name of the configuration file. The default is to use the name of the router with the suffix -confg. Press Return to accept the default filename, or enter a different name for the file, then press Return.

  • Page 37

    Install Field Replaceable Units (FRUs) Retrieve the Configuration File for RSPs Retrieve the saved configuration and copy it to NVRAM by accessing the router through a console terminal, or from a remote terminal. Step 1 Enter the enable command at the EXEC prompt (>), and then enter a privileged-level password, as follows: Router>...

  • Page 38

    Install Field Replaceable Units (FRUs) The console display indicates whether or not the operation was successful. A series of exclamation points (!!!!) and [OK] (as shown in the preceding example) indicates that the operation was successful. A series of periods (. .

  • Page 39

    Install Field Replaceable Units (FRUs) Remove and Install Port Adapters Screw Carrier Lower edge Upper edge...

  • Page 40

    Note First remove the VIP from the chassis before removing the port adapter from the VIP. See the “Remove and Install an Interface Processor, Filler, VIP, or RSP” section on page 29 for instructions. Step 1 Remove the screw that secures the port adapter (or blank port adapter), as shown in A. Step 2 Grasp the handle and carefully pull it out of its slot, away from the edge connector at the rear of the slot.

  • Page 41

    Install Field Replaceable Units (FRUs) Remove and Replace the Power Supply Redundant power supplies support online insertion and removal (OIR); if you remove one power supply, the second power supply immediately ramps up to maintain uninterrupted operation. In this case, proceed to Step 2. If you have only one power supply, you must turn off power before removing and replacing it.

  • Page 42

    Install Field Replaceable Units (FRUs) For the DC-input power supply: Use a screwdriver to loosen the captive installation screws on the terminal block cover, lift the cover, use the wire cutters to cut the nylon strain-relief ties, and then remove the three power leads (remove the ground lead last) from the terminal block. See below. OT SHIP WITH POWER SUPPLY FASTENER TO BE FULLY ENGAGED ALLED...

  • Page 43

    ScriptBuilder, ScriptShare, SlideCast, SMARTnet, TransPath, Unity, Voice LAN, Wavelength Router, and WebViewer are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That’s Possible, and Empowering the Internet Generation, are service marks of Cisco Systems, Inc.; and Aironet, ASIST,...

Comments to this Manuals

Symbols: 0
Latest comments: