Joovy CocoonX2 Manual page 6

EN FR ES
• Always store tow bar in a clean dry place.
• Before and after each use, inspect tow bar and discontinue use should it malfunction or become damaged.
• Not for use at high speeds. DO NOT exceed 10 MPH (16 km/h).
• Each child must wear an approved safety helmet when riding in the product in trailer mode.
• Always ensure your bicycle brakes function properly. Braking distance is increased when pulling a trailer.
• The trailer is wider than most bicycles. Allow extra clearance when near curbs, signs, parked cars and other obstacles.
• Do not turn sharply. A bicycle with a trailer requires a wide turning radius.
• Install a rearview mirror on your bicycle to check on children in the trailer.
13 Assembling and Using the Trailer Mode Attachment
To ensure safe operation of your trailer, please follow these instructions carefully.
14 Unpacking the Product
• Carefully remove tow bar and all parts from the box and plastic bag.
• Remove any packing materials from the product.
• Identify the parts (tow bar with tether, safety flag and documents [not shown]) with the pictures in Figure 14.1.
• Remove all cardboard and plastic coverings from any areas of the components.
• Discard all packaging properly. Do not allow children to play with them.
Adult assembly is required for this product. No tools required for bicycles with a quick release axle on the rear wheel.
Bicycles without a quick release axle on the rear wheels will require an adjustable wrench.
15 Removing the Coupler Attachment from the Tow Bar
• Locate the coupler attachment on the tow bar.
• To remove, carefully rotate the locking clamp off of the tow bar. See Figure 15.1. Pull the locking pin out from the tube.
• Remove the coupler attachment from the tow bar tube. See Figure 15.2.
16 Installing/Uninstalling Coupler Attachment for Bicycles with Quick Release Rear Axles
• Flip the rear axle quick release lever open and remove the nut and spring from the opposite side. See Figure 16.1.
• Hold the lever and pull out the axle skewer with spring. See Figure 16.2.
• Completely remove the skewer while leaving the wheel in place.
• Place the coupler over the left side of the axle with the flat side of the coupler attachment facing inward against the frame of the bicycle. Insert
the skewer through the wheel hub (and the coupler) and hook it onto the bicycle frame dropout. See Figure 16.3.
NOTE: The wide end of the spring should face outward and touch the quick release hub. See Figure 16.4.
• Replace the spring and then the nut onto the skewer. Turn the nut to tighten and then close the quick release lever. See Figure 16.5.
• Check the rear wheel to ensure it is tight and operating correctly.
• To remove this accessory please reverse the instructions in this section.
17 Installing/Uninstalling Coupler Attachment for Bicycles with Rear Hub Nuts
• Loosen the left rear wheel hub nut with a wrench.
• Remove the hub nut and washer from the axle. See Figure 17.1.
• Place the coupler attachment onto the axle with the flat side facing inward against the frame of the bicycle. See Figure 17.2.
• Replace the washer and the bicycle hub nut onto the axle and turn the nut to tighten. See Figure 17.3.
• Tighten the hub nut securely with a wrench.
• Check the rear wheel to ensure it is tight and operating correctly.
• To remove this accessory please reverse the instructions in this section.
18 Attaching/Detaching the Tow Bar to the Trailer
• Tilt the stroller so it is resting on the handle bar and the rear wheels.
• Remove one of the front swivel wheels by opening the quick release lever and pulling the front wheel post from the housing. Repeat this
process to remove the other front wheel. Return the quick release levers to their closed positions.
• Remove the locking pin with clamp from the attachment tube (located on the lower front end of the stroller) by opening the clamp and
unscrewing the nut.
• Insert the tow bar into the housing on the front of the trailer until the holes on the sides line up. See Figure 18.1.
• Insert the locking pin through the holes and rotate the quick release lever to the closed position to secure in place. See Figure 18.2.
• Pull the tow bar away from the stroller to ensure it is securely installed.
• To remove this accessory please reverse the instructions in this section.
WARNING
!
WARNING
!
Use caution not to get pinched by the locking clamp.