Advertisement
Quick Links
A S S E M B L Y I N S T R U C T I O N S
TABLE OF CONTENTS:
Pg. 1
Pg. 1
Assembly
Pg. 2 - Pg. 9
Pg. 7
Cable Mapping Diagram
Fold-out Pg. 10
Exploded View Diagram
Fold-out Pg. 11
Pg. 12
Back Page
SP-405
Pectoral Contractor
© 2003 TuffStuff Fitness Equipment, Inc.
A m e r i c a ' s P r e m i e r E x e r c i s e E q u i p m e n t
47 3/4"
55 1/4"
L 47 3/4" W 55 1/4" H 54 3/4"
Revision Date 02-21-03
SP-405 Rev1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for TuffStuff SP-405
Summary of Contents for TuffStuff SP-405
-
Page 1: Table Of Contents
A m e r i c a ’ s P r e m i e r E x e r c i s e E q u i p m e n t © 2003 TuffStuff Fitness Equipment, Inc. SP-405 Rev1... -
Page 2: Introduction
Stuff Equipment 2. Neatly organize and identify all parts according to the This Tuffstuff product has been built to precise quality Parts List and the Exploded View Diagram. standards and has been carefully packaged to ensure that damage will not occur during shipment. - Page 3 Rubber Donuts (#13). Note: Be sure the label on the Top Plate Selector Bar (#7) facing out, as shown above, before sliding the Top Plate Se- lector Bar (#7) onto the Guide Rods (#3). SP-405 Pectoral Contractor...
- Page 4 Weight Stack Frame (#1) using two Hex Head Cap Cam Plates (#34) to the Front Frame (#29). Screws 1/2-13 X 3 3/4 (#60), four Flat Washers SAE 1/2” (#27), and two Nylon Insert Lock Nuts 1/2-13 (#20). SP-405 Pectoral Contractor...
- Page 5 Loosely Fasten: Do not completely fasten this hardware as- sembly at this time, as it will be completely fastened later in the assembly process. Note: Refer to Fig A on fold-out page 10 for further detailed il- lustration of this assembly. SP-405 Pectoral Contractor...
- Page 6 Top Plate Selector Nylon Insert Jam Lock Nut 3/8-16 (#21). Bar (#7). Fully Fasten: Proceed to fully fasten this hardware assem- bly. Note: Refer to Fig B on fold-out page 10 for further detailed il- lustration of this assembly. SP-405 Pectoral Contractor...
- Page 7 Socket Head Cap Screws 1/4-20 X 3/4 (#48). Use the supplied num Cam Plate (#34). Hex Key 3/16” (#64) to fasten these Socket Head Cap Screws. Note: Refer to Fig C2 on fold-out page 10 for further illustra- tion of this assembly. SP-405 Pectoral Contractor...
-
Page 8: Cable Adjustment
3. Re-tighten the Finished Hex Nut 1/2-13 (#62) to complete the adjustment. Caution: Make sure the Cable Hex Tap Bolt 1/2-13 X 3 (#61) is threaded at least 1/2” into the threaded socket of the Front Frame (#29) once the cable ad- justment has been completed. SP-405 Pectoral Contractor... - Page 9 (#5), in the position as shown above, and secure it into place using two Flat Head Socket Cap Screw 3/8-16 X 3 (#23). ing four Hex Head Cap Screws 1/4-20 X 3/4 (#19), and four Flat Washers 1/4” (#18). SP-405 Pectoral Contractor...
- Page 10 Hex Head Cap Screws 3/8-16 X 1 1/4 (#49), and two position as shown above, using two Hex Head Cap Screws 3/8-16 X Flat Washers SAE 3/8” (#17). 3 (#53), and two Flat Washers SAE 3/8” (#17). SP-405 Pectoral Contractor...
-
Page 11: Parts List
BALL BEARING #W 516 BNH0628 OFFSET PULLEY BRACKET UP0121 DECAL-SIMPLEX II (1 7/8 X 5 3/16) BNH1199 ALUMINUM CAM PLATE BNH1153 DECAL-TUFFSTUFF (2 3/4 X 19 1/16) BNH1200 SEAT PAD UP0317 DECAL-EXERCISE SP-405 PECTORAL BNH1190 BACK PAD UP0822 DECAL-LARGE TUFFSTUFF LOGO... -
Page 12: Warranty
L I M I T E D W A R R A N T Y TuffStuff warrants to the original purchaser only that TuffStuff equipment will be free from defects in material and workmanship. The warranty and remedies set forth herein are conditioned upon proper storage, installation, use, maintenance and conformance with any recommendations of TuffStuff.
Need help?
Do you have a question about the SP-405 and is the answer not in the manual?
Questions and answers