Advertisement
Quick Links
A S S E M B L Y I N S T R U C T I O N S
TABLE OF CONTENTS:
Pg. 1
Pg. 1
Assembly
Pg. 2 - Pg. 8
Pg. 7
Pg. 9
Exploded View Diagram
Fold-out Pg. 10
Cable Mapping Diagram
Fold-out Pg. 11
Back Page
SP-402
Shoulder Press
© 2003 TuffStuff Fitness Equipment, Inc.
A m e r i c a ' s P r e m i e r E x e r c i s e E q u i p m e n t
50 3/4"
L 50 3/4" W 55 1/4" H 54 3/4"
Revision Date 06-12-02
55 1/4"
SP-402 Rev0
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for TuffStuff SP-402
Summary of Contents for TuffStuff SP-402
-
Page 1: Table Of Contents
A m e r i c a ’ s P r e m i e r E x e r c i s e E q u i p m e n t © 2003 TuffStuff Fitness Equipment, Inc. SP-402 Rev0... -
Page 2: Introduction
Stuff Equipment This Tuffstuff product has been built to precise quality 2. Neatly organize and identify all parts according to the standards and has been carefully packaged to ensure that Parts List and the Exploded View Diagram. - Page 3 Rubber Donuts (#15). Note: Be sure the label on the Top Plate Selector Bar (#9) facing out, as shown above, before sliding the Top Plate Se- lector Bar (#9) onto the Guide Rods (#4). SP-402 Shoulder Press...
- Page 4 Loosely Fasten: Do not completely fasten this hardware as- sembly at this time, as it will be completely fastened later in the assembly process. Note: Refer to Fig A on fold-out page 11 for further detailed il- lustration of this assembly. SP-402 Shoulder Press...
- Page 5 Hex Head Cap Screws 1/2-13 X 4 3/4 (#57), four Flat Loosely Fasten: Do not completely fasten this hardware as- Washers SAE 1/2” (#29), and two Nylon Insert Lock Nuts 1/2-13 sembly at this time, as it will be completely fastened later in (#22). the assembly process. SP-402 Shoulder Press...
- Page 6 Press Main Frame (#31) as shown above. Discard the cable Lock Nuts 3/8-16 (#23). fishing string once completed with this process. Note: Be sure the Cable (#39) is routed properly into the groove of the Nylon Pulleys. SP-402 Shoulder Press...
- Page 7 Frame (#31), in the position as shown above, using four Hex Head 3/8-16 X 1 1/4 (#51), and four Flat Washers SAE 3/8” (#19). Cap Screws 3/8-16 X 3 (#52), and four Flat Washers SAE 3/8” (#19). SP-402 Shoulder Press...
-
Page 8: Cable Adjustment
Guide Rod Retainer (#5) Shrouds (#2, #3), in the position as shown above, and slide them all ing four Hex Head Cap Screws 1/4-20 X 3/4 (#21), and four Flat the way down. Washers 1/4” (#20). SP-402 Shoulder Press... - Page 9 (#6). FIG. 25 Attach the Plastic Shroud Lid (#11) to Guide Rod Retainer (#5), in the position as shown above, and secure it into place using two Flat Head Socket Cap Screws 3/8-16 X 3 (#25). SP-402 Shoulder Press...
-
Page 10: Parts List
U-STYLE TAPPED HOLE NUT 3/8-16 BNH1211 SHOULDER PRESS MAIN FRAME UP0839 DECAL-SIMPLEX II (1 7/8 X 5 3/16) BNH1199 PIVOT AXLE UP0807 DECAL-TUFFSTUFF (2 3/4 X 19 1/16) BNH1200 BOTTOM CROSS BRACE UP0989 DECAL-EXERCISE SP-402 SHOULDER PRESS BNH1187 REAR CROSS BRACE UP0836... -
Page 11: Warranty
L I M I T E D W A R R A N T Y TuffStuff warrants to the original purchaser only that TuffStuff equipment will be free from defects in material and workmanship. The warranty and remedies set forth herein are conditioned upon proper storage, installation, use, maintenance and conformance with any recommendations of TuffStuff.
Need help?
Do you have a question about the SP-402 and is the answer not in the manual?
Questions and answers