Advertisement
Quick Links
A S S E M B L Y I N S T R U C T I O N S
TABLE OF CONTENTS:
Pg. 1
Pg. 1
Assembly
Pg. 2 - Pg. 9
Pg. 7
Cable Mapping Diagram
Fold-out Pg. 10
Exploded View Diagram
Fold-out Pg. 11
Pg. 12
Back Page
SP-407
Single Column
© 2003 TuffStuff Fitness Equipment, Inc.
A m e r i c a ' s P r e m i e r E x e r c i s e E q u i p m e n t
42 1/2"
L 42 1/2" W 43 1/4" H 90 1/2"
Revision Date 06-26-02
43 1/4"
SP-407 Rev0
Advertisement
Related Manuals for TuffStuff SP-407
Summary of Contents for TuffStuff SP-407
-
Page 1: Table Of Contents
A m e r i c a ’ s P r e m i e r E x e r c i s e E q u i p m e n t © 2003 TuffStuff Fitness Equipment, Inc. SP-407 Rev0... -
Page 2: Introduction
Stuff Equipment This Tuffstuff product has been built to precise quality 2. Neatly organize and identify all parts according to the standards and has been carefully packaged to ensure that Parts List and the Exploded View Diagram. - Page 3 (#3), in position as shown above, allowing the first one Guide Rods (#3). to rest on top of the Rubber Donuts (#13). Note: Lubricate the Guide Rods (#3) with silicone or teflon lu- bricant at this time. SP-407 Single Column...
- Page 4 Head Cap Screws 1/2-13 X 3 1/2 (#56), four Flat Washers SAE four Flat Washers SAE 3/8” (#53), and two Nylon Insert Jam Lock 1/2” (#60), and two Nylon Insert Lock Nuts 1/2-13 (#59). Nuts 3/8-16 (#51). SP-407 Single Column...
- Page 5 (#31), two Hex Head Cap Screws 3/8-16 X 3 3/4 (#49), four Flat Washers SAE 3/8” (#53), and two Nylon Insert Lock Nuts 3/8-16 (#52). Note: Refer to the Exploded View Diagram on page 11 for fur- ther illustration of this assembly. SP-407 Single Column...
- Page 6 1/2” Rd. (#15-Labeled G). Rd. (#14-Labeled E). Make sure the cable passes between the pul- leys and the Cable Retainers (#31). Note: Refer to the Cable Mapping Diagram on page 10 for fur- ther illustration of this routing. SP-407 Single Column...
- Page 7 Shoulder Bolts 3/8 X 3/4 (#64), and two Nylon Insert 1/4 (#63), and a Strap Bracket (#65) to the end of the Cable. Lock Nuts 5/16-18 (#62). Note: Refer to the Cable Mapping Diagram on page 10 for fur- ther illustration of this routing. SP-407 Single Column...
-
Page 8: Cable Adjustment
1. Loosen the bottom Finished Hex Nut 1/2-13 (#61). 2. Adjust the top Finished Hex Nut 1/2-13 (#61) to give the cable proper tension. 3. Re-tighten the bottom Finished Hex Nut 1/2-13 (#61) to complete the adjustment. SP-407 Single Column... - Page 9 Align the edge of the Weight Shroud (#2) with the Shroud Edge Protector (#9) to the edge of the Weight Shroud (#2). grooves of the Plastic Shroud Gap Cover (#7) and the Plastic Shroud Edge Protector (#9). SP-407 Single Column...
- Page 10 FIG. 27 Attach the Handles (#32) to the Top Upright Connector (#27) using two Hex Head Cap Screws 3/8-16 X 3 3/4 (#49), four Flat Washers SAE 3/8” (#53), and two Nylon Insert Lock Nuts 3/8-16 (#52). SP-407 Single Column...
-
Page 11: Parts List
DECAL-TUFFSTUFF (2 3/4 X 19 1/16) BNH1200 PUSH PULL PIN 1/2 X 2 7/8 LIGHT SPRING BNH0542 DECAL-EXERCISE SP-407 SINGLE COLUMN 4 1/2 X 26 BNH1198 BRONZE BUSHING 1 X 1 1/4 X 3/4 X 1 1/2 X 1/8 BNH0527... -
Page 12: Warranty
L I M I T E D W A R R A N T Y TuffStuff warrants to the original purchaser only that TuffStuff equipment will be free from defects in material and workmanship. The warranty and remedies set forth herein are conditioned upon proper storage, installation, use, maintenance and conformance with any recommendations of TuffStuff.
Need help?
Do you have a question about the SP-407 and is the answer not in the manual?
Questions and answers