Carel pCO3 Technical Leaflet page 16

PRELIMINARY NOTES FOR THE INSTALLER: COMPARISON BETWEEN pCO
3
• the pCO family controllers do not have the connector using the programming key code PCO201KEY0. To program the controller, use
the new Smart
Key (PCOS00AKY0) available from September 2005. Otherwise use WinLoad ver. 3.35 and higher:
An application cannot be run from the Smart Key;
• unlike the pCO 2 , there is no fuse between J1 and J2. All pCO
No external fuse is required;
• a further terminal J24 (in place of the fuse) is provided for the power supply to the ratiometric probes (+5 VREF), as well as 20 Vdc to supply
a secondary terminal, such as the aria terminal (TAT***), in alternative to the standard one;
• the terminal J11 (connection to the pLAN network) in the fi rst prototypes of the pCO
• the LEDs near the dipswitches for setting the pLAN address have been moved between connectors J3 and J4;
• the red probe power supply overload LED has been removed.
pCO3 simulator:
3
If testing the pCO with a simulator, note that the pCO
availability of the latter.
Procedure for setting the address of the controller and terminal
Setting the address of the controller
3
The pCO controller does NOT have dipswitches for setting the pLAN address. The address must be set by software, as for the pCO
The procedure is as follows:
1. switch the pCO 3 off ;
2. prepare a standard Carel terminal with the address set to 0 (not necessary if the pCO
following paragraph;
3. connect the terminal to the pCO
4. disconnect any other devices connected in the pLAN from the pCO
5. switch the pCO 3 on, pressing the UP + ALARM buttons at the same time. This combination of buttons is the same on the built in
terminal.
Alternatively, on the PCOT terminals, use the combination of the
6. after a few seconds, the following screen will be displayed:
PLAN ADDRESS: 0
UP: INCREASE
DOWN: DECREASE
ENTER: SAVE & EXIT
7. to modify the address simply use the UP and DOWN buttons and then press ENTER to confi rm.
8. now set the pLAN address of the terminal and confi gure the pLAN network.
Setting the address of the terminal
pCOI/pCOT terminal
The address of the terminal is set using the DIPSWITCHES on the rear of the terminal.
pGD0/1/2/3 terminal
The default value of the address is 32.
The address of the terminal can only be set after having connected the power supply via the telephone connector.
To enter confi guration mode, press the  buttons at the same time (even when the terminal is already on), in all the versions, for at least
5 seconds; the following screen will be displayed, with the cursor fl ashing in the top left corner:
Display address
setting.........:nn
I/O Board address:xx
• to modify the address of the terminal (display address setting) press the  button once: the cursor will move to the address fi eld (nn).
• use the  buttons to select the desired value, and confi rm by pressing the  button. If the value selected is diff erent than the value
saved previously, the screen shown below will be displayed, and the new value will be saved to permanent memory.
Display address
changed
If the fi eld nn is set to the value 0, the terminal will communicate with the pCO
and the "I/O Board address: xx" fi eld will not be displayed, as it no longer has meaning.
+050003299 - 1.6 03.08.2011
Fig. 6
2
3
;
3 family controllers have an internal thermal protector on the power supply.
3
only has a pitch of 3.81, rather than the 5.08 on the pCO
simulator cannot be used in place of the pCO
3
(terminal J11);
menu
and buttons.
3 controller using the "point-to-point" protocol (not pLAN)
8
AND pCO
3
3
simulator. Contact CAREL for the
3
Built-In terminal is used). For this operation, see the
2
2
;
1/XS
.