Subscribe to Our Youtube Channel
Related Manuals for Avalue Technology EEV-EX14A1.1
Summary of Contents for Avalue Technology EEV-EX14A1.1
- Page 1 EEV-EX14 A1.1 EEV-EX14 COM Express Type 6 Evaluation Carrier Board User’s Manual Ed – 30 August 2017 Part No. E2047EX1400R...
-
Page 2: Table Of Contents
EEV-EX14 User’s Manual Contents Getting Started ..................... 4 Safety Precautions ....................4 Packing List ......................4 Hardware Configuration..................5 Product Overview ....................6 Jumper and Connector List..................7 Setting Jumpers & Connectors ................10 2.3.1 Clear CMOS (JBAT1) ......................10 2.3.2 S3 signal selector (JPWR1)..................... - Page 3 User’s Manual 2.3.29 Front Audio connector (JAUDIO2) ..................25 2.3.30 Battery connector (BH1) ......................25 2.3.31 EDP connector (EDP1) ......................26 EEV-EX14 Expansion Boards ................27 2.4.1 Product Overview ........................27 2.4.2 Jumper and Connector List ..................... 28 EEV-EX14 Expansion Boards Setting ..............29 2.5.1 Audio Expansion Card for Front Audio (KJAUDIO1) ...............
-
Page 4: Getting Started
EEV-EX14 User’s Manual 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. -
Page 5: Hardware Configuration
User’s Manual 2. Hardware Configuration EEV-EX14 User’s Manual 5... -
Page 6: Product Overview
EEV-EX14 User’s Manual 2.1 Product Overview 6 EEV-EX14 User’s Manual... -
Page 7: Jumper And Connector List
User’s Manual 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. - Page 8 EEV-EX14 User’s Manual Connectors Label Function Note AUDIO1 Audio connector ATX1 ATX1 Power connector 12 x 2 wafer, pitch 4.2mm ATX2 Power connector 2 x 2 wafer, pitch 4.2mm ATX2 COM1 Serial port 1 connector D-Sub 9 pin CFAN1 CPU fan connector 1 4 x 1 wafer CFAN2 CPU fan connector 2...
- Page 9 User’s Manual connector PCIE1 PCI Express x16 connector PCIEXPRESS_164V PCIE2 Digital Display Interfaces (DDI) slot PCIEXPRESS_164V PCIE3 PCI Express x4 connector PCIEXPRESS_64V PCIE4 PCI Express x1 connector PCIEXPRESS_36V JCD1 CD-ROM Audio Input connector 4 x 1 wafer, pitch 2.54mm SATA 1/2/3/4 Serial ATA connector Front Audio connector 5 x 2 wafer, pitch 2.54mm...
-
Page 10: Setting Jumpers & Connectors
EEV-EX14 User’s Manual 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* Clear CMOS * Default 2.3.2 S3 signal selector (JPWR1) Control S3* NO Control of S3 Signal PWR_S3 * Default Note: SLP_S3# PIN1(Input)：Control by power button PIN2(Output)：Control power IC PIN3(Input)：Module board to Carrier board singal 10 EEV-EX14 User’s Manual... -
Page 11: Pcie Signal Selector (Jpcie1)
User’s Manual 2.3.3 PCIE signal selector (JPCIE1) Default* Signal +3.3V PCI Express Differential Transmit Pairs JPCIE1 PCIE [0] PCIE PCIE PCIE PCIE PCIE PCIE PCIE SEL=LOW PCIE3 LAN2 PCIE4 MIIN-PCIE1 EXPRESS1 SEL=HIGH LAN2 PCIE4 MIIN-PCIE1 EXPRESS1 X 2.3.4 PCIE2 (DDI) signal selector (JHDMI1) HDMI/SDVO* Display Port Signal... -
Page 12: Com1 Pin 9 Signal Select (Jri1)
EEV-EX14 User’s Manual 2.3.5 COM1 Pin 9 signal select (JRI1) Ring* +12V *Default 2.3.6 SUPER I/O Address select (JSIO1) High: 4Eh/4Fh Low: 2Eh/2Fh* Signal +3.3V RTSA# *Default 12 EEV-EX14 User’s Manual... -
Page 13: At Power Selector (Jat1)
User’s Manual 2.3.7 AT Power selector (JAT1) 12V Control* Signal SLP_S3# 12V Always Enable +12V +3VSB *Default Note: When jumper 2-3 closed：Module board always have +12V 2.3.8 ATX1 Power connector (ATX1) Signal PIN PIN Signal PSON# +5VSB +12V +12V EEV-EX14 User’s Manual 13... -
Page 14: Atx2 Power Connector (Atx2)
EEV-EX14 User’s Manual 2.3.9 ATX2 Power connector (ATX2) Signal PIN PIN Signal +12V +12V 2.3.10 CPU Fan connector/ System Fan connector 1/ System Fan connector 2 (C_FAN1/ S_FAN1/ S_FAN2) CFAN2 Signal +12V CPUFANIN1 CPUFANOUT1 SFAN1 CFAN1 Signal Signal +12V +12V SYSFANIN CPUFANIN SYSFANOUT... -
Page 15: Floppy Connector 1 (Fdc1)
User’s Manual 2.3.11 Floppy connector 1 (FDC1) Signal Signal DRVDEN0 INDEX# MOA# DSA# DIR# STEP# TRAK0# RDATA# HEAD# DSKCHG# EEV-EX14 User’s Manual 15... -
Page 16: Printer Connector (Jprt1)
EEV-EX14 User’s Manual 2.3.12 Printer connector (JPRT1) Signal Signal STB- LPT_AFD# LPT_ERR# LPT_INIT# LPT_SLIN# LPT_ACT# LPT_BUSY LPT_PE LPT_SLCT 2.3.13 IR connector (JIR1) Signal IRRX IRTX 16 EEV-EX14 User’s Manual... -
Page 17: Serial Port 2 Rs422/485 Connector (J422/485)
User’s Manual 2.3.14 Serial Port 2 RS422/485 connector (J422/485) 422 Mode Signal Signal 485 Mode Signal Signal DATA- DATA+ 2.3.15 Serial Port 2 RS232 connector (JCOM2) Signal Signal RXDD TXDD EEV-EX14 User’s Manual 17... -
Page 18: General Purpose I/O Connector (Jdio1)
EEV-EX14 User’s Manual 2.3.16 General Purpose I/O connector (JDIO1) Signal Signal SMB_CLK SMB_DAT 2.3.17 Multi-purpose connector (JCN3) Signal Signal SER0_TX SER0_RX SER1_RX SER1_TX SLEEP# LID# PP_TPM PP_TPM +3VSB 18 EEV-EX14 User’s Manual... -
Page 19: Front Panel Connector (Jfp1)
User’s Manual 2.3.18 Front panel connector (JFP1) Signal Signal CASEOPEN# AT_BN EXT_PWRBTN# SATA_LED# SYS_RERST# EXT_PWRBTN# Short = AT Signal Power Button Reset Power LED HDD LED Case Open Open = ATX 2.3.19 SPI selector (JSPI1) Signal BIOS_DIS1# Note: jumper 1-2 closed can disable module board SPI FLASH，use carrier board SPI FLASH EEV-EX14 User’s Manual 19... -
Page 20: Carrier Board Spi Flash Programming (Jspi2)
EEV-EX14 User’s Manual 2.3.20 Carrier board SPI FLASH programming (JSPI2) Signal Signal +3VSB SPI_CS# SPI_CLK SPI_MOSI SPI_MISO SPI_HOLD# 2.3.21 LCD backlight brightness adjustment connector (JVR1) Signal LVDS_BKLT_CTR Variation Resistor (Recommended: 4.7KΩ, >1/16W) 20 EEV-EX14 User’s Manual... -
Page 21: Lcd Inverter Connector (Jbkl1)
User’s Manual 2.3.22 LCD Inverter connector (JBKL1) Signal +12V_BKL BKLEN LVDS_BKLT_CTRL/PWM Note: For inverter with brightness control function through LVDS_BKLT_CTRL/PWM signal (Pin-4) , it is possible to control the brightness level by carrier board's JVR1 pin2. In this case, R179 would be removed to disconnect the PWM control signal from COMExpress module (CN1A Pin-B84). -
Page 22: Lvds Connector (Lvds1)
EEV-EX14 User’s Manual 2.3.23 LVDS connector (LVDS1) Signal Signal +3.3V +3.3V LVDS_DDC_SD LVDS_DDC_SC LVDSA_DATA0 LVDSA_DATA1 LVDSA_DATA0# LVDSA_DATA1# LVDSA_DATA2 LVDSA_DATA3 LVDSA_DATA2# LVDSA_DATA3# LVDSB_DATA0 LVDSB_DATA1 LVDSB_DATA0# LVDSB_DATA1# LVDSB_DATA2 LVDSB_DATA3 LVDSB_DATA2# LVDSB_DATA3# LVDSA_CLK LVDSB_CLK LVDSA_CLK# LVDSB_CLK# +12V +12V 2.3.24 USB Connector 4 & 5 (JUSB1) Signal PIN PIN Signal... -
Page 23: Lpc Port Connector (Jlpc1)
User’s Manual 2.3.25 LPC port connector (JLPC1) Signal PIN PIN Signal +3.3V RESET# FRAME# CLOCK SERIRQ +5VSB LPC_DRQ1# 2.3.26 SPDIF connector (JSPDIF1) Signal +3.3V S/PDIF-IN S/PDIF-OUT EEV-EX14 User’s Manual 23... -
Page 24: Cd-Rom Audio Input Connector (Jcd1)
EEV-EX14 User’s Manual 2.3.27 CD-ROM Audio Input connector (JCD1) Signal CD_L CD_R 2.3.28 7.1ch Audio connector (JAUDIO1) Signal Signal LFE-OUT CEN-OUT SURR-R-OUT SURR-L-OUT SIDESURR-R-OU SIDESURR-L-OU CEN-JD SURR-JD Note： SIDESURR-JD Pin to pin to the Audio Expansion Card KJAUDIO2 connector 24 EEV-EX14 User’s Manual... -
Page 25: Front Audio Connector (Jaudio2)
User’s Manual 2.3.29 Front Audio connector (JAUDIO2) Signal PIN PIN Signal MIC2-L-IN MIC2-R-IN ACZ_DET# LINE2-R-OUT MIC2_JD Note： Pin to pin to the Audio Expansion Card KJAUDIO1 LINE2-L-OUT LINE2-JD connector 2.3.30 Battery connector (BH1) Signal +3.3VSB EEV-EX14 User’s Manual 25... -
Page 26: Edp Connector (Edp1)
EEV-EX14 User’s Manual 2.3.31 EDP connector (EDP1) Signal EDP_TX3# EDP_TX3 EDP_TX2# EDP_TX2 EDP_TX1# EDP_TX1 EDP_TX0# EDP_TX0 EDP_AUX EDP_AUX# +3.3V +12V Signal +VDD_EDP +VDD_EDP +VDD_EDP EDP_AUX +VDD_EDP EDP_BRIGHT_CTRL +VDD_EDP LVDS_BKLT_EN/ EDP_BKLT_EN +3.3V EMB_HPD SMB_THRM_CLK SMB_THRM_DATA ALS_INTR# TP_VDD_LPP 26 EEV-EX14 User’s Manual... -
Page 27: Eev-Ex14 Expansion Boards
User’s Manual EEV-EX14 Expansion Boards 2.4.1 Product Overview ct Overview Digital Display Interface Card HDMI Level Shift Riser Card Display Port Riser Card EEV-EX14 User’s Manual 27... -
Page 28: Jumper And Connector List
EEV-EX14 User’s Manual AUDIO Expansion Card(7.1channel & Front audio) 2.4.2 Jumper and Connector List Connectors Label Function Note GDVI1 DVI connector GPCIE1 PCIE connector (into the PCIE2) PCIEXPRESS_164V HDMI connector NHDMI1 NPCIE1 PCIE connector(into the PCIE2) PCIEXPRESS_164V ZDP1 Display port connector ZPCIE1 PCIE connector (into the PCIE2) PCIEXPRESS_164V... -
Page 29: Eev-Ex14 Expansion Boards Setting
User’s Manual EEV-EX14 Expansion Boards Setting 2.5.1 Audio Expansion Card for Front Audio (KJAUDIO1) Signal PIN PIN Signal MIC2-L-IN MIC2-R-IN ACZ_DET# LINE2-R-OUT MIC2_JD AUDIO Expansion Card (7.1channel & Front audio) LINE2-L-OUT LINE2-JD 2.5.2 Audio Expansion Card for 7.1ch Audio (KJAUDIO2) Signal PIN PIN Signal...
Need help?
Do you have a question about the EEV-EX14A1.1 and is the answer not in the manual?
Questions and answers