Table of Contents
Advertisement
Quick Links
RolMotion M-868 Roller Blind Drive
Contents
Operating and assembly
1
2
General information on these instructions
2.1
2.2
2.3
2.4
2.5
3
3.1
3.2
4
4.1
4.2
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
1
5.8
1
5.9
2
6
2
7
2
8
2
9
10
2
11
2
12
2
13
3
13.1
3
3
3
4
4
RolMotion M-868 Roller Blind Drive
1
Operating and assembly instructions
5
5
Follow these instructions for safe and proper use. Observe
all assembly instructions. Incorrect assembly can lead
5
to serious injuries. Please keep this operating manual
for future reference to ensure that it can be accessed
5
throughout the entire service life of the product!
5
The German operating manual is the original version.
All documents in other languages are translations of the
5
original version.
6
All rights reserved in the case of patent, utility model or
design registrations.
6
2
General information on these instructions
6
The content structure is based on the life cycles of the electric
motor drive (hereinafter referred to as „the product").
The manufacturer reserves the right to make changes
6
to the technical data in these operating instructions. In
some cases, this technical data may differ from those of
7
the respective product version; however, the functional
information will not undergo significant changes or become
invalid. The current version of the technical specifications
7
may be requested from the manufacturer at any time.
No claims may be asserted against the manufacturer
7
as a result of this provision. Deviations from textual or
visual statements may occur depending on the product's
7
technical development, features and accessories. Deviating
information for special versions will be provided by the
manufacturer in the sales documentation. Other information
shall remain unaffected by these provisions.
7
7
8
8
8
9
9
9
9
10
10
138251101_EN_1219
Advertisement
Table of Contents
Related Manuals for elero RolMotion M-868
Summary of Contents for elero RolMotion M-868
-
Page 1: Table Of Contents
RolMotion M-868 Roller Blind Drive Contents 5.7.1 Programming the first transmitter 5.7.2 Programming additional transmitters Operating and assembly instructions Deleting the radio connection between transmitters and receivers General information on these instructions Programming or deleting further blind positions 8 Standards and guidelines... -
Page 2: Instructions
The product is intended for use in facade constructions as a drive for electrically powered roller shutters and blinds. • Failure to observe the safety regulations and information presented in these operating The elero calculation program is central to defining the instructions drive. www.elero.com/en/downloads-service/elero- •... -
Page 3: Product Description
During operation, it executes radial followed, which can lead movements. to serious, possibly fatal, ‰ Commissioning of the RolMotion M-868 with elero irreversible injuries or assembly cable or radio transmitter for setting various death. functions. -
Page 4: Mechanical Fastening
Secure the drive axially in the Damage to RolMotion M-868 due to ingress of moisture support! ►On devices with protection class IP 44, the ends of all Ⓒ A ttach the blind to the shaft. -
Page 5: Connection Example For Rolmotion M-868 230 V / 50 Hz
►The end positions must be adjusted using the elero side connection of the cable ends or plugs (cable feed- assembly cable (see Fig. 6) or an elero wall or hand-held through) can also be implemented according to protection transmitter (see Fig. 7). -
Page 6: Changing/Deleting The End Positions
By default, the lower end position has been set. Non-standard setting for placement of the blind slats at the lower end position: See chapter 5.6. Adjustment of the variant B end position is complete. 6 | EN © elero GmbH... -
Page 7: Variant C: Fixed Upper And Lower Limit Stop
Adjustment of the variant D end position is complete. On the (additional) The status display transmitter to be lights briefly. The drive programmed, press the is in learning mode programming button [P]. (up/down travel) for approximately 2 minutes. © elero GmbH EN | 7... -
Page 8: Deleting The Radio Connection Between
Transmitter programming | Travel profiles Travel profiles Programming additional transmitters Operating procedure Result The RolMotion M-868 drive has the two travel profiles default mode and whisper mode. On the (additional) The status display lights briefly. The blind transmitter to be program med, press the [UP ▲]... -
Page 9: Servicing
(see chapter suitable, inspected and structurally stable climbing aids. 5.5) ►Work on the electrics may only be performed by Fig. 8 Troubleshooting the RolMotion M-868 personnel described in the section „Safety notes on electrical installation“. Servicing Removal for scrap The RolMotion M-868 is maintenance-free. -
Page 10: Comments On Eu Declaration Of Conformity
Declaration of conformity | Technical data and dimensions Comments on EU Declaration of Conformity elero GmbH hereby declares that the RolMotion M-868 tubular drive is in compliance with all applicable regulations of Machinery Directive 2006/42/EC and the Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.elero.com/en/downloadsservice/... - Page 11 Technical data and dimensions © elero GmbH EN | 11...
- Page 12 GmbH Maybachstr. 30 info@elero.de We reserve the right to make technical changes Drive technology 73278 Schlierbach, Germany www.elero.com...