Page 1
99 317.GB.80I.0 LPIN 226 NOVA (Type PSM 317 : + . . 01001) LPIN 266 NOVA (Type PSM 318 : + . . 01001) Disc mower Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr. Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr.
Page 2
Dear Farmer You have just made an excellent choice. Naturally we are very happy and wish to congratulate you for having chosen Pöttinger. As your agricultural partner, we offer you quality and efficiency combined with reliable servicing. In order to assess the spare-parts demand for our agricultural machines and to take these demands into consideration when developing new machines, we would ask you to provide us with some details.
TABLE OF CONTENTS WARNING SIGNS CE sign ..............5 Attention! Meaning of warning signs.......... 5 Observe Safety ATTACHING TO TRACTOR Hints in the Attaching in general ........... 6 supplement! Driveshaft ..............6 Road Transport ............6 Special attachment ............ 7 Guard plates and protective aprons ......
WArning signs CE sign The CE sign, which is affixed by the manufacturer, indicates outwardly that this machine conforms to the engineering guideline regulations and the other relevant EU guidelines. Recommendations EU Declaration of Conformity (see supplement) for work safety By signing the EU Declaration of Conformity, the manufacturer declares that the machine being All points referring brought into service complies with all relevant safety and health requirements.
ATTACHing TO TrACTOr Attaching in general Driveshaft 1. Observe safety hints in supplement-A. • Please also observe the hints in the chapter “Special attachment” 2. Mark off the implement at the tractor's three- point linkage. • Secure locking bolts with linch pins. •...
ATTACHing TO TrACTOr Special attachment Because of the different lifting gears on various tractors special attaching kits are to be used. • see supplement-D • see Spare Parts List also. Maximum drive shaft angle Most drive shafts in continuous operation may only be angled to a maximum 25°...
ATTACHing TO TrACTOr Guard plates and protective aprons Transport position (< 3 m) Attention! Guard plates and protective aprons can be raised when When both protective elements have been raised and maintenance work is to be done. are engaged in the holder (), the total width of the unit For safety reasons is less than m.
ATTACHing TO TrACTOr Quick-coupler (1) Attaching problems Safety • For lifting gear with a crossbar between the lower links hints: damage to the cardan shaft could occur when lowering - M o u n t s n a p see supplement-A1 the attached implement.
Page 10
ATTACHing TO TrACTOr Snap connector (Weiste triangle) Pay particul arattention before initial attachment to Tractor! Attention! For front lifting gear with double-action hydraulic cycle (danger of damage)! Remedy: - Switch control valve to single-action - Convert front lifting gear to single-action function (bypass line) through a specialist work shop.
For mowing, the power take-off shaft drive should be switched to turn to the left. TD40/94/16 NOVAALPIN 226 Remedy, if the tractor’s power take-off shaft drive cannot be switched to turn to the left: Mount the drive shaft in the gearing in position L...
sTArTing WOrk Driving motor speed The machine can be adapted to the r.p.m. (540 rpm, 1000 rpm) being used. Fit both V-belt pulleys (Ø212 mm and Ø160 mm) in the relevant position (see diagram). - 12 - 0300-GB EinsAtz_317...
sTArTing WOrk Safety hints In the event of a collision • Stop immediately and switch 1. Check off the drive. - Check the condition of knives and the knife holder. • Carefully check the i m p l e m e n t f o r - Check cutting drums for damage (see also chapter d a m a g e .
COLLisiOn sAFETY DEViCE Collision safety device Function of collision safety device Attention! If the mower encounters an obstacle, the springloaded The collision safety device is available on the Type-B mounting frame only and not on the Weiste triangle pin (1) is released and the cutter bar can swing back. It is not the mounting frame.
MAinTEnAnCE Safety point Parking in the ope Safety points! • Turn engine off when adjustment, service and repair When parking in the open for work is to be done. long periods of time, clean • Turn engine off piston rods and then coat when adjustment, with grease.
1. Lift one side of the mower bar (X1) and support. NovaAlpin 226 : X1 = 20,5 cm NovaAlpin 266: X1 = 22,5 cm • The side where the oil refill screw is located remains on the ground.
The arrow on the cutter blade shows the cutter disc's direction of turn. - To install, clean back plates from varnish. NOVAALPIN 226 V-belt tension When the correct V-belt tension is set, the gap between indicator and bush is “0 mm”.
MAinTEnAnCE AnD sErViCE Compensating plate Fit the accompanying compensating plate (2) when the sliders (1) are worn. Lubrication - 1 - 0500-GB Wartung_317...
MAinTEnAnCE Checking wear on mowing blade holders Wearing parts are: Attention! - mounting of mowing blades (0) Danger of accident - bolts of mowing blades (1) if wearing parts are worn If such wearing parts are worn out they must not be used any longer.
MAinTEnAnCE AnD sErViCE Changing the Cutter Blades Holder for a quick change of cutter blades (up to 2003 model) 1. Insert lever (H) horizontally between cutter disc and holder (30) Attention! 2. Push movable holder (30) down using lever For Your Safety (H).
MAinTEnAnCE AnD sErViCE Changing the Cutter Blades (from 2004 model) 1. Insert lever from left or right side on the cutter disc ”Pos A” until it stops. 2. Swing lever from ”pos. A” to ”pos. B” and push the movable holder (30) down. 3.
The defined use of the mower unit The NOVAALPIN 226 (Type PSM 17) und NOVAALPIN 266 (Type PSM 18) mower is intended solely for normal use in agricultural work. • The mowing of grassland and short stemmed fodder.
Page 24
The original cannot be copied ... Things will run better with genuine Pöttinger parts • Quality and precise fitting The decision must be made, ”original” or ”imitation”? The decision is often governed by price and a ”cheap buy” can sometimes be very expensive. - Operating safety.
Recommendations for work safety suppLEMEnT - A Recommendations for work safety 6.) Transport of persons prohibited All points refering to safety in this manual are indicated a. The transport of persons on the machine is not permitted. by this sign. b.
DriVEsHAFT Supplement - B Matching driveshaft to tractor Rules for working To determine the actual length required, hold the two Never exceed the maximum p. t. o. speed when using halves of the driveshaft side by side. the implement. Important! - When the p.t.o.
Page 27
DriVEsHAFT Supplement - B How a cam type cut out safety clutch works This overload clutch switches the torque transmitted to zero if overloaded. To revert to normal operation, stop the p.t.o. drive briefly. The clutch reengages at a speed below 200 rpm. IMPORTANT! Re-engaging is also possible by decreasing the p.t.o.
suppLEMEnT-D Special attachment Because of the different lifting gears on various tractor types special attaching kits are to be used. See spare parts list also. Universal mounting frame (k2) This mounting frame offers more possible pinning positions for the various tractor lifting gears. This enables good cutter unit adaptation to the various tractor types.
rEpArAir insTruCTiOns Repairs on the cutter bar • Adjust markings in a line (K1, K2). • Only screw the nut (M) on when there is sufficient thread length in order to prevent any damage. • Secure nut (M) against loosening. - with „Loctite 242“...
iMpOrTAnT! ADDiTiOnAL inFOrMATiOn Combination of tractor and mounted implement The mounting of implements on the front or rear three point linkage shall not result in exceeding the maximum permissible weight, the permissible axle loads and the tyre load carrying capacities ot the tractor. The front axle of the tractor must always to be loaded with at least 20 % of the unladen weight of the tractor.
Page 34
iMpOrTAnT! ADDiTiOnAL inFOrMATiOn 3. CALCULATION OF THE REAL FRONT AXLE LOAD T V tat (If with the front mounted implement (G ) the required minimum front ballasting (G ) cannot be reached, the weight of the front mounted V min implement has to be increased to the weight of the minimum ballasting at the front!) Record the calculated real front axle load and the permissible front axle load of the tractor into the table.
Page 35
__________________________________________________________________________________ (full address of company - where this concerns authorized agents within the Common Market, also state the company name and manufacturer) declare in sole responsibility, that the product Disc mower NOVAALPIN 226 Type 317 NOVAALPIN 266 Type 318 __________________________________________________________________________...
Page 36
Im Zuge der technischen Weiterentwicklung La société PÖTTINGER Ges.m.b.H améliore Following the policy of the PÖTTINGER Ges. arbeitet die PÖTTINGER Ges.m.b.H ständig constamment ses produits grâce au progrès m.b.H to improve their products as technical an der Verbesserung ihrer Produkte. technique.
Need help?
Do you have a question about the NovaAlpin 226 and is the answer not in the manual?
Questions and answers