Kenmore 790.3670 Series Use & Care Manual page 9

Before Setting Surface ControRs
Assembly of the Surface Burner Heads, Burner Caps and Burner Grates (Porcelain Cooktop
mode_s)
Htis very important to make sure that aHH o f the Surface Burner Heads, Surface Burner Caps and Surface Burner Grates
are instaHHed correctHy and at the correct Hocations,
1, Remove aHH packing tape from cooktop area, Remove aHH
Burner Caps and Burner Heads,
2, Discard aHH packing materiaH Hocated under Burner Heads (if
appHcabHe),
3, To repHace the Burner Heads & Caps, match the Hetters
Hocated under center of Burner Caps with the HettersHocated
inside Burner Heads (Figure 1),
4, Match Burner Skkts with Burner Heads and Burner Caps (see
Figure 1), RepHacethe Burner Heads and Caps on cooktop
(see Figure 2), CarefuHHy aHignthe Electrodes into shot or hoHe
of each Burner Head (Figure 3), Note: The Burner Heads
shouHd sit flat on Cooktop Burner Skirts,
5, PHace the removabHe oven vent cover over the fixed oven
vent cover,
6, Unpack Burner Grates and position on the cooktop,
Figure 1
¢
Figure 2
Figure 3 align into slot or hole for each
Burner Head
REMEMBER-- DO NOT ALLOW SPmLLS, FOOD, CLEANmNG AGENTS OR ANY OTHER MATERmAL TO ENTER THE
GAS ORmFmCE HOLDER OPENmNG. AHways keep the Burner Caps and Burner Heads in pHacewhenever the surface
burners are in use,
AssernMy of the Surface Burner Heads, Burner Caps and Burner Grates (Ceramic G_ass
Cooktop mode_s)
Htis very important to make sure that aHH o f the Surface Burner
Heads, Surface Burner Caps and Surface Burner Grates are
instaHHed correctHy and at the correct Hocations,
1, Be sure to foHHow the HnstaHHation Hnstructions before instaHHing
and using your new range,
2, Remove aHH packing tape from cooktop, Remove Burner Caps
and Burner Heads (See Figure 4),
3, Discard aHH packing materiaH Hocatedunder aHH Burner Heads (if
appHicabHe),
4, To repHaceBurner Heads & Caps, match the HettersHocated under
center of Burner Caps with the HettersHocated inside Burner Head BridgeBurnerHead
(onHypositions A & F are marked with Hetters - See Figure 5),
PHaceaHH Burner Heads & Caps on the cooktop (See Figure 4) Bridge
whiHecarefuHHy aHigningthe EHectrodes into shots or holies of the Burner
- End
Burner Heads (Figure 7), Note: The Burner Heads shouHdsit flat
Cap
on Cooktop Burner Skirts,
5, RepHaceBridge Burner Caps, These incHudeone Bridge Burner ......
Center Cap (rectanguHarshaped) and the two Bridge Burner End Bridge
Caps (The Bridge Burner End Caps wiHH f it either the front or rear Burner
Bridge Burner Head Hocations),Make sure that the tabs Hocated Center
Cap
under the Bridge Burner Caps faHH i nto the shotsHocatedin the
Bridge Burner Head (See arrows in Figure 6) and that aHH t he Bridge ..... Bridge
Burner Caps Hie flat and evenHyon the Bridge Burner Head, Burner
6, Unpack Burner Grates, NOTE: Do not force End Burner Grates - End
down on cooktop, Be careful to line up the 2 Grate Pins located Cap
on each of the 2 End Burner Grates into the PiHotholies Hocated
on top of the Burner Caps (See Figure 8), Position Burner Figure6
Grates on cooktop and check that aHH the Burner Grate HegsHie
on the gHasssurface,
7, PHaceCenter Burner Grate between the end Burner Grates,
" i
Head ,"f:,_, '
Figure5
Electrodes
must align into slot or hole
for each Burner Head
Figure 7
Grate Pin
Burner
c_p
Figure8
REMEMBER -- DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE
GAS ORIFICE HOLDER OPENING. AHways keep the Burner Caps and Burner Heads in prince whenever the surface
burners are in use, 9
!! . ...........
i ii!!