Table of Contents
Advertisement
3. Press "
" to enable-
the beep;
4. Press "
" to go back to the homepage.
8.14 Cup light
This function enables or disables the cup lighting.
The lights come on each time coffee beverages or hot milk is de-
livered and during each rinse cycle.
To disable or enable this function, proceed as follows:
1. Press "
" (B2) to enter the menu;
2. Press
(B10) or
pears on the display (B);
3. Press " " to enable-
cup lighting;
4. Press "
" to go back to the homepage.
8.15 Background
You can choose the display background from the following 4
alternatives: "SHADED BLUE", "STAINLESS STEEL", "COFFEE
BROWN", "DARK BLUE". Proceed as follows:
1. Press "
" (B2) to enter the menu;
2. Press
(B10) or
appears on the display (B);
3. Press "
". The available backgrounds appear on the
display;
4. Select the required background by pressing the chosen
panel. The appliance goes back to the settings menu with
the new background;
5. Press "
" to go back to the homepage.
8.16 Bluetooth
This function enables or disables the protection PIN to connect to
the appliance from a device.
1. Press "
" (B2) to enter the menu;
2. Press
(B10) or
on the display (B);
3. Press "
" to access the function;
4. Enable or disable the PIN protection by pressing -
or
5. Press "
" twice to go back to the homepage.
The preset PIN is "0000". You are recommended to customise the
PIN directly from the APP.
Please note!
The serial number of the appliance, visible in the "Bluetooth"
function, enables it to be identified unambiguously when an
association is created with the APP.
or disable-
(B8) until " CUP LIGHTING" ap-
or disable-
(B8) until "
BACKGROUND"
(B8) until " BLUETOOTH" appears
;
8.17 Emptying the circuit
To avoid the water in the circuit freezing if the appliance is to be
left idle for a long period of time, or before taking it to customer
services, we recommend emptying the water circuit.
Proceed as follows:
1. Press "
" (B2) to enter the menu;
2. Press
(B10) or
EMPTYING" appears on the display (B);
3. Press "
";
4. "EMPTY GROUNDS CONTAINER AND DRIP TRAY": extract and
empty the grounds container (A10) and drip tray (A14).
Press "
5. "INSERT GROUNDS CONTAINER AND DRIP TRAY": insert
the
the drip tray complete with grounds container;
6. "PLACE 0.5l CONTAINER UNDER SPOUTS, PRESS OK TO
START": position a container under the coffee spouts (A8)
and hot water spout (C6). Press "
Danger of burns!
Do not leave the appliance unattended while hot water is being
delivered.
10. "INSERT WATER TANK, PRESS OK TO CONTINUE": insert the
water tank and press "
11. "WATER CIRC. EMPTYING UNDERWAY": wait for the appli-
ance to empty the circuit; (Important: hot water from the
spouts!). As the water circuit empties, the appliance could
become noisier. This is part of normal operation.
12. "EMPTY DRIP TRAY": remove, empty and reposition the drip
tray, then press "
13. "EMPTYING COMPLETE: PRESS OK TO TURN OFF": press "
". The appliance goes off.
Please note!
When turned on again, the appliance asks for the circuit to be
filled: follow the instructions from point 3 of section "5.4 Setting
up the appliance".
13
(B8) until "
WATER CIRCUIT
";
" (fig. 8);
7. "RINSING
PLEASE WAIT": the ap-
pliance performs a rinse
cycle from the coffee
spouts;
8. "EMPTY WATER TANK":
extract the tank (A16)
and empty it completely,
then press "
(fig. 10);
9. (If the filter is installed)
10
"REMOVE WATER SOFTEN-
ER FILTER": remove the
filter from the tank. Press
"
";
" (fig. 6);
";
UNDERWAY,
"
Advertisement
Table of Contents
Troubleshooting
