Table of Contents
Advertisement
•
The message "TURNING OFF, PLEASE WAIT" is displayed,
then the appliance performs a rinse cycle and goes off
(standby).
Please note!
If you will not be using the appliance for some time, first empty
the water circuit (see section "8.17 Emptying the circuit
unplug from the mains socket as follows:
•
first turn the appliance off by pressing the
(fig. 9);
•
release the main switch (A21) at the back of the appliance
(fig. 2).
Important!
Never press the main switch while the appliance is on.
8. MENU SETTINGS
8.1
Rinsing
Use this function to deliver hot water from the coffee spouts (A8)
and hot water/steam spout (C6), if inserted, to clean and heat
the appliance's internal circuit.
Place a container with a minimum capacity of 100ml under the
coffee and hot water spouts (fig. 8).
To enable the function, proceed as follows:
1. Press "
" (B2) to enter the menu;
2. Press
(B10) or
on the display (B);
3. Press "
" to start rinsing.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. After a few seconds, hot water is delivered first from the
coffee spouts, then from the hot water/steam spout (if
inserted) to clean and heat the appliance's internal circuit.
"RINSING UNDERWAY, HOT WATER FROM SPOUTS" appears
on the display, together with a progress bar which fills
gradually as preparation proceeds;
5. To stop rinsing, press "
stop automatically.
Please note!
•
If the appliance is not used for more than 3-4 days, when
you turn it on again, we strongly recommend performing
2/3 rinses before use;
•
After cleaning, it is normal for the grounds container (A10)
to contain water.
8.2 Descaling
For instructions on descaling, see section "19. Descale".
i
"), then
(B8) until "
RINSING" appears
" or wait for rinsing to
8.3 Water filter
For instructions on how to install the filter (C4), see section "21.
Water softener filter".
8.4 Beverages settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage, except cold
button
coffee, cold milk and chocolate.
1. Press "
2. Press
appears on the display (B);
3. Press "
display;
4. The reference user profile is highlighted on the display. The
values are displayed on vertical bars. The default value is
indicated by the
highlighted by the solid part of the vertical bar;
5. To go back to the settings menu, press "
To scroll and display the beverages, press "
6. To reset the default values for the beverage displayed, press
"
RESET";
7. "CONFIRM RESET?": to confirm, press "
press "
8. "DEFAULT VALUES SET": press "
The beverage has been reset to the default values. Continue with
the other beverages, or go back to the settings menu.
Please note!
•
To change the beverages in another profile, go back to the
homepage, select the required profile (B11) and repeat the
procedure.
•
To reset all the beverages in the profile, see section "8.18
Default values
•
"
8.5 Adjust time
To adjust the time on the display (B), proceed as follows:
1. Press "
2. Press
on the display (B);
3. Press "
4. Press
until the current time is displayed;
5. To confirm, press "
then press "
The time is now set.
11
" (B2) to enter the menu;
(B10) or
(B8) until "
". The values for the first beverage appear on the
symbol, while the current value is
");
" (B2) to enter the menu;
(B10) or
(B8) until "
". The time setting panel appears on the display;
or
corresponding to the hours and minutes
" (to cancel, press "
" to go back to the homepage.
DRINKS SETTINGS"
".
";
" (to cancel,
".
SET TIME" appears
"),
Advertisement
Table of Contents
Troubleshooting
