Advertisement
3. SPECiFiCATion
Motor . . . . . . . . . . . . . . . . . . . . . . . . . 1500W - 230V
speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5700rpm
saw Blade diameter. . . . . . . . . . . . . . . . . . . Ø254mm
saw Blade Arbor. . . . . . . . . . . . . . . . . . . . . . . Ø20mm
Max. depth of 90 ° cut . . . . . . . . . . . . . . . . . . . 75mm
Max. depth of 45 ° cut . . . . . . . . . . . . . . . . . . . 60mm
4. ASSEMBLY
4.1
the unit is best assembled upside down on a smooth and flat surface. ensure that the saw blade is fully retracted under the work
table before turning the unit over.
4.2
Assemble a leg to each corner of the unit using two 12mm long bolts and two small washers. ensure that the two rectangular holes at
the top of each leg are aligned with the moulded rectangular spigots on each corner of the unit. see A & B in fig.2. do not fully tighten
the bolts at this stage.
4.3
When all four legs are in place assemble the cross struts as shown in fig.3 using two 12mm long bolts, two nuts and two small
washers at each end of the strut. two of the struts are 20mm longer than the other pair and should be assembled to the legs above
the side of the unit that has the on/off switch and the opposite side above the dust extractor. each strut has a narrow returned edge
and a wide returned edge. the wide returned edge of each strut should always be nearest to the underside of the unit. note that the
ends of the cross struts are angled to match the outward angling of the legs. All fixings should be hand tight at this stage.
4.4
At one end of each side table is an aluminium guide track which will form an extension to the main rip fence guide track on the front of
the main unit. two joining plates are provided to ensure that the three sections of the track are properly aligned. Place a large washer
over a 12mm bolt and screw it into each joining plate as shown in fig.4. turn the two side tables upside down and slide the joining
plates into the slots at the end of the track as shown in fig.4. Hand tighten the bolts so that the plates are drawn up under the tracks as
shown in fig.5 ensuring that the washer rests on the outside face of the guides.
4.5
Place the two side tables upside down onto the floor beside the main unit as shown in fig.6 and slide them up to the main unit so that
the joining plates slide into the aluminium rip fence guide at either end. Place another large washer over a 12mm bolt and screw into
place on the rip fence guide as shown in fig.7. using the four cheese headed screws provided attach each side table to the main table
using two screws on each side. tighten these screws and the joining plate bolts.
4.6
Identify the four shorter table stays and attach two to each side table. the two returned edges of the stays should be facing the
underside of the side tables. each stay shares one of the leg fixings at each corner. remove the leg fixing that lines up with the
appropriate fixing on the far edge of each side table and hold the stay in position whilst replacing the bolt. use a 12mm bolt, washer
and nut to fix the stay to the edge of the side table. repeat the process for all four stays.
4.7
take the rear extension table and place it upside down on the floor at the back edge of the main work table. one side of the table has
slots which should be lined up with the threaded holes in the back of the main table and the other side has two holes for mounting the
stays. use two 12mm bolts to fix the extension to the main table. Attach the two longer stays to the rear extension table in the same
Main table . . . . . . . . . . . . . . . . . . . . . . 440 x 625mm
side extension sizes (x2): . . . . . . . . . . 245 x 585mm
rear extension size: . . . . . . . . . . . . . . 320 x 435mm
table with extensions. . . . . . . . . . . . . . 915 x 940mm
dust extraction Port (taper). . . . . . . . . . . . . . Ø40mm
fig.2
fig.4
Original Language Version
fig.3
fig.5
ts10seW
Issue: 2 - 12/01/10
Advertisement
