Advertisement
% DO NOT use the saw where there are flammable liquids, solids or gases such as paint solvents, etc.
% DO NOT allow children to operate the saw.
% DO NOT operate the saw if any parts are missing as this may cause failure and/or personal injury.
% DO NOT leave the saw operating unattended.
% DO NOT carry the saw with your finger on the power switch.
% DO NOT use the saw for a task it is not designed to perform.
% DO NOT use a blade which is damaged, cracked, distorted or has missing teeth.
% DO NOT tamper with, or remove, blade guard.
% DO NOT operate the saw when you are tired, under the influence of alcohol, drugs or intoxicating medication.
% DO NOT get the saw wet or use in damp or wet locations.
% DO NOT hold unsecured workpiece in your hand whilst cutting.
! Secure non-stable workpiece with a clamp, vice or other adequate holding device.
! Avoid unintentional starting.
! Before making a cut ensure that all accessories and adjustment fixings are fully tightened.
! Only use saw blades that are specifically designed for use with this machine.
! Always use the side fence supplied or a securely fixed straight edge guide when doing a rip cut (along the length of the grain).
% DO NOT force the saw to cut but allow it to operate at its normal working speed.
% DO NOT attempt to carry the saw by its power cable.
% DO NOT bring the power cable into contact with sharp objects (such as the blade) or edges or sources of heat.
% DO NOT attempt to unplug the power cable by pulling on the cable itself.
% DO NOT use the saw with any other manufacturers accessories.
% DO NOT reach under the workpiece whilst the blade is cutting. Keep hands away from the cutting area and do not attempt to remove cut
material whilst the blade is still turning.
% DO NOT wedge the blade guard open. If the unit is accidentally knocked or dropped check that the blade guard still operates easily and
smoothly. If the blade guard is damaged stop using the saw until the guard is repaired or replaced.
% DO NOT fit or use a saw blade that is intended to cut metal. Always ensure that the saw is fitted with the correct wood cutting blade.
% DO NOT substitute an abrasive wheel for the saw blade.
! Evaluate your work area before using the saw e.g. partitions may conceal electric cables or water piping.
% DO NOT allow the blade to come into contact with nails or other steel fixings used in old timber or existing timber structures. Inspect the
workpiece before commencing cutting and remove any potential hazards.
% DO NOT attempt to stop the saw by pressing on the side of the blade.
% DO NOT start the saw with the blade in contact with the workpiece. Allow the blade to run up to speed before proceeding to cut.
2. INTRODUCTION & SPECIFICATION
The SCS1400 circular saw is intended for cutting all types of timber products including solid timber, plywood and reconstituted sheet material
such as chipboard and MDF. It is adjustable for depth of cut and angle of cut up to 45
of unintentional starting. The saw also has a dust extraction port and a directed flow of air keeps the cut line visible.
Specification.
Power supply . . . . . . . . . . . . . . . .230V
Input power . . . . . . . . . . . . . . .1400W
No load blade speed . . . . . . .4500rpm
Blade size . . . . . . .Ø184mm x 20 x 2.6
Blade arbor . . . . . . . . . . . . . . .Ø20mm
fig. 1
Auxiliary
handle
Depth of cut
adjustment
lever
SCS1400 - 2 - 200603
Cutting depth - 0
Cutting depth - 45
Acoustic pressure . . . . . . . . . .94dB(A)
Acoustic power . . . . . . . . . . .107dB(A)
Typical weighted vibration . . . . .4.6m/s
Lock-off
button
Dust
extraction
port
Rear 0
-45
O
O
lock knob
and features a safety lock off button to reduce the risk
O
. . . . . . . . . . .64mm
O
. . . . . . . . . . 45mm
O
2
Trigger switch
Allen key
Blade wrench
Items packed in carton:
1. Circular saw unit.
2. Side fence sawing guide.
3. Allen key for blade changing.
4. Wrench for blade changing.
5. Dust extraction nozzle.
Handle
Forward
0
-45
O
lock knob
Side fence
O
Side fence
lock knob
Cutting line
indicators
0
-45
O
O
Dust
extraction
nozzle
Advertisement
