Advertisement
fig.6
way that the side stays were attached. now tighten all leg fixings, cross braces and stays.
4.8
turn the assembly upright and check that the main table and extensions form a flat and step free surface.
4.9
raise the blade and riving knife by turning the blade depth adjustment handle (10) clockwise.
4.10
remove the butterfly nut, bolt and washer from the blade guard and slide the guard over the riving knife until the hole in the knife
aligns with the hole in the guard. slide the bolt through both the knife and guard and replace the washer and butterfly nut.
4.11
take the mitre gauge and slide its metal bar into one of the slots on either side of the blade. Hold the mitre face extension bar in front
of the mitre gauge allowing the two sliding bolts at the back to drop into the slots in the mitre face. tighten the thumb wheels.
4.12
Attach the flexible dust extraction hose (18) to the outlet on the blade guard (9). Attach the other end to the dust extraction inlet on the
back of the saw.
4.13
lay the measurement scales provided, into the shallow recess on the upper face of the rip fence guide. fix in place with the 6 small
self tapping screws provided. do not fully tighten so that the measurement scale can slide within the bounds of the fixing slots.
4.14
take the rip fence (5) and lift the locking handle to the horizontal position. Place the rip fence down over the rip fence guide
so that it rests flat against the left hand side of the saw blade and move the handle downwards to lock it in position. look through the
sight glass and adjust the position of the measurement scale so that zero is aligned with the sight glass mark. tighten the three fixing
screws that hold the left hand measurement scale. release the rip fence and place it flat against the right hand side of the blade.
repeat the alignment process for the right hand measurement scale and tighten the fixing screws. slide the rip fence away from the
blade.
5. OPERATION
the saw is fitted with a "no-Volt" on/off switch. If the power supply is interrupted whilst the saw is on, the saw has to be switched back on
again when the power supply is restored. to switch on press the green "I" switch. to switch off press the red button.
Caution: switch off the machine and unplug from the power supply before carrying out any adjustments, maintenance work or blade changes.
5.1.
Fitting and removing the saw blade guard and dust extractor
5.1.1. to remove the saw blade guard (8), unscrew the wing nut and remove the bolt, then lift off the guard.
5.1.2. to replace it, slide it over the riving knife aligning the slot in the guard with the knife (3), and align it so that the holes in both the guard
and the riving knife are aligned.
5.1.3. Insert the bolt and fit the wing nut.
5.1.4. tighten the wing nut sufficiently so that the
guard rests on the saw table top (1) but will
lift easily when a workpiece is pushed
towards the blade and also returns to rest
on the saw table after the workpiece has
been removed.
5.1.5. A suitable vacuum extraction system should
be connected to the outlet of the vacuum
extraction adaptor port at the rear of the table.
5.1.6. connect one end of the flexible hose (18) to
the dust extractor duct (9) and the other end
to the vacuum extraction adaptor port at the
rear of the table.
5.2.
Adjusting the rip fence
5.2.1. the rip fence can be fitted to either side of
the table top (1)
5.2.2. lift the rip fence locking lever (6) and slide
the fence to the required position.
5.2.3. use the scale (20) on the front of the table
top to set the rip fence so that the work
piece is sawn to the required width.
5.2.4. Push down the rip fence locking lever (6) to
clamp the rip fence in position.
5.3.
Adjusting the cutting depth
5.3.1. set the saw blade to the required cutting
depth by turning the blade depth adjustment
wheel (10).
5.3.2. turning the wheel anti-clockwise increases
the cutting depth, and clockwise decreases it.
fig.7
Original Language Version
fig.1 repeated
ts10seW
Issue: 2 - 12/01/10
Advertisement
