Download Print this page

Specification; Operation - Sealey SMS216.V2 Instructions

Ø216mm sliding compound mitre saw

Advertisement

2. INTRODUCTION
Powerful 1450W motor. Features integral aluminium workpiece supports which store inside the aluminium base to save space and prevent loss.
Fitted with a 24-tooth TCT blade for fresh wood. Can be fitted with Model No. SMS216B multipurpose blade for use with mild steel, aluminium
and wood with nails. Features double slides which can be locked at different lengths allowing greater control over the desired length of cut. Max
cut of up to 310mm at 0° bevel. Unit is also fitted with a powerful LED work light and laser guide to help produce accurate cuts. Supplied with
workpiece clamp, dust extraction bag and fitted with carry handle. Features locking increments at Mitre stops 0°,15°, 22.5°, 31.6°, 35°, 45° Left &
Right.

3. SPECIFICATION

Model no ............................................................. SMS216.V2
Blade size ...................................Ø216 x 2.8 x Ø30mm (24T)
Dust extraction port ................................Ø36mm/OD Ø40mm
Motor power ................................................................1450W
No-load speed .......................................................... 5000rpm
Positive mitre lock ........................... 0°, 15°, 22.5°, 31.6°, 45°
Supply ............................................................................230V
Cross Cut (0
Bevel x 0
0
0
Mitre Cut (0° Bevel x 45° Table): ........................ 62 x 215mm
Bevel Cut (45° Bevel x 45° Table): ..................... 34 x 215mm
Consumable Parts: ...SMS216B - Multipurpose Cut-Off Saw Blade Ø216 x 2.4mm/Ø30mm 32tpu
4. FEATURES
14
13
12
11
19
fig.1
5. ASSEMBLY
5.1.
Secure the saw to a flat, stable surface by inserting screws through the holes drilled in the machine's feet. The area should be well lit
and have sufficient room to use the machine safely.
5.2.
Unless using with a dust extractor, fit the dust bag (fig.1.15) onto the dust port (fig.1.16). If using dust extraction, use a suitable
adaptor to couple the dust port and hose.

6. OPERATION

NOTE: Ensure all Safety Instructions in Section 1 are read and understood and carried out before use.
WARNING! To prevent accidental starting that could cause possible serious personal injury, assemble all parts, make sure
adjustments are complete, and make sure all fasteners are secure before connecting saw to power supply.
WARNING! Saw should never be connected to power supply when you are assembling parts, making adjustments, installing or
removing blades and when not in use.
6.1.
BLADE LOCK (fig.1.3, fig.2)
6.1.1.
To raise the blade; pull the guard release lever (fig.1.3, fig.2), disengage the Release Knob (fig.2) and lift the blade.
6.1.2.
To lower, pull the guard release lever, which will allow the blade to be lowered (fig.2)
6.1.3.
The blade assembly may be locked down by pushing the Release Knob (fig.2) in fully.
6.1.4.
The saw may only be carried with the blade locked down.
© Jack Sealey Limited
Table) .......................... 62 x 310mm
15 ,16
17
10
Original Language Version
18
5
8
9
1 On/Off Trigger
, 2
1
2 Laser On/Off Button
(far side)
3 Guard Release Lever
3
4 Blade guard
5 Laser (see fig.7)
6 Mitre lock
4
7 Mitre Locking Handle
8 Mitre Scale
9 Mitre Table
10 Fence
11 Clamp Assembly
12 Bevel Angle Stop Adjuster
13 Bevel Scale
14 Bevel Lock Lever
15 Dust Bag
16 Dust Extraction Port
17 Trenching Depth
6
Adjustment Screw
7
18 Carrying Handle
19 Side Support
SMS216.V2 Issue:1
18/03/21

Advertisement

loading