Advertisement
Ensure the machine is situated on a solid surface, adequate for supporting the weight of the machine and the workpiece.
check the alignment of moving parts regularly, for safest performance keep the machine clean at all times.
turn off the machine before raising the blade
Avoid unintentional starting.
regularly remove, clean and inspect the blade brush.
remove any adjusting keys and wrenches from the bandsaw before turning it on.
replace or repair damaged parts. use recommended parts only. unauthorised parts may be dangerous and will invalidate the
warranty.
Keep hands and body clear of the work table when operating the bandsaw.
maintain correct balance and footing, ensure the floor is not slippery and wear non-slip rubber soled footwear.
remove ill fitting clothing, ties and loose jewellery, and tie back long hair.
Ensure there are no flammable or combustible materials near the work area.
DO NOT leave the machine running unattended.
DO NOT operate the machine if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT use the bandsaw for a task it is not designed to perform.
DO NOT use bandsaw near to flammable liquids, solids or gases, such as paint solvents and including waste wiping or cleaning rags.
DO NOT use damaged or deformed bandsaw blades.
DO NOT remove the safety guard whilst in use.
DO NOT hold the workpiece by hand.
DO NOT touch the workpiece immediately after cutting, it may be very hot.
DO NOT operate the machine when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT allow children or untrained persons to operate the machine. Keep them away from the work area.
When not in use unplug from the mains supply and make every effort to ensure that the machine is childproof.
2. INTRODUCTION & SPECIFICATION
the sm353cE.V2 has a large cutting capacity making it ideal for Industrial and Agricultural engineering applications. A 24V system for
coolant pump and motor controls gives added safety to the operator.
the bandsaw is not suitable for cutting wood and, if used for this purpose, the insurer will not provide coverage.
the saw arm is fitted with hydraulic damping to prevent it being dropped onto the workpiece and to ensure a smooth cutting performance.
the heavy-duty single phase electric motor has an over-current sensor to cut the power in the event of blade jamming.
the saw is manufactured to comply with supply of machinery (safety) regulations 1992 (s.I.3073) and is fully cE approved.
2.1.
SPECIFICATION.
capacity 90° round .............................................................Ø230mm
capacity 90° square/rectangular H x W ......................230 x 370mm
capacity 45° round .............................................................Ø185mm
capacity 45° square/rectangular H x W ......................230 x 185mm
Blade size .....................................................25.0 x 0.89 x 3035mm
Cutting Chart for Flat and Round Bar
Recommended blade teeth per inch (tpi) for nominal cut length
cut length
<13mm
6-16mm
tpi
24
A
B
c
D
motor Pulley
3. ASSEMBLY
3.1.
UNPACKING.
3.1.1. unpack the bandsaw and inspect all parts. If any parts are damaged contact your distributor.
3.1.2. unbolt from the transport skid and place on a firm, level surface.
3.1.3. clean all rust protected surfaces with kerosene, diesel oil, or a mild solvent. Do not use cellulose based solvents as these will damage painted
surfaces.
3.2.
ASSEMBLY.
3.2.1. Attach the pulley cover with the screws and washers provided. close when attached and secure with thumb screw.
8-22mm
17-40mm
18
14
8
E
f
G
H
saw Pulley
Original Language Version
Blade speeds ................................................. 25, 40, 51, 71mtr/min
motor Power ...........................................................................1120W
Power supply .................................................................... 230V/1ph
Weight .....................................................................................285kg
Recommended Pulley Selection for Various Metals
>38mm
Material
4
Tool, stainless or alloy steel.
Bearing bronze.
Medium to high carbon steel.
Hard brass or bronze. Cast iron.
Low to medium carbon steel.
Soft brass.
Aluminium. Copper. Brass.
Saw Pulley
Blade Speed
Motor Pulley
Large (E)
25m/min
Small (A)
Large (F)
40m/min
Medium (B)
Medium (G)
51m/min
Medium (C)
Small (H)
71m/min
Large (D)
sm353cE.V2
Issue: 3 - 15/12/11
Advertisement
