Cleaning Mode; Commands Particular To Camera - Canon ZR70 MC A Service Manual

4-3 Cleaning Mode

When cleaning the head with hard-type cleaning tape (DY9-1384-000), set up the cleaning mode according to the procedure given
below.
Note : After head cleaning, be sure to restore the settings to normal.
ST EP PROCEDURE
1 1) Make setting shown at right.
2) Increases DT by 2.
(Change bit-02 to 1 from 0.)
(Example: 80 → 82)
3) Perform ST ORE. (Press PAUSE key. ↑
2 1) Change over to the normal mode and turn OFF the power supply.

4-4 Commands Particular to Camera

<Outline>
(1) The commands particular to camera are provided for checking the operation.
(2) Make preparation according to the table below and carry out the desired commands particular to camera.
(3) To restore any setting back to the original status, press the PAUSE key (STORE) for each item again in the "ST" mode.
Turning the power OFF/ON resets all the settings.
ST EP PROCEDURE
CAM SPECIAL COMMAND
WB SET 1) Make setting shown at right.
2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
LOCK 2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
T URBO 2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
OUT DOOR 2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
INDOOR 2) Execute ST ORE. (Press PAUSE.)
IRIS 1) Make setting shown at right.
OPEN 2) Execute ST ORE. (Press PAUSE.)
IRIS 1) Make setting shown at right.
CLOSE 2) Execute ST ORE. (Press PAUSE.)
AGC 1) Make setting shown at right.
MAX 2) Execute ST ORE. (Press PAUSE.)
AGC 1) Make setting shown at right.
MIN 2) Execute ST ORE. (Press PAUSE.)
COLOR 1) Make setting shown at right.
BAR 2) Execute ST ORE. (Press PAUSE.)
White 1) Make setting shown at right.
100% 2) Execute ST ORE. (Press PAUSE.)
White 1) Make setting shown at right.
50% 2) Execute ST ORE. (Press PAUSE.)
CHAPTER 3. INFORMATION FOR REPAIR · SERVICE HINTS
MONIT OR
CS Function ADDR MODE
0 10 0111 ST
↑ ↑ ↑ ↑
↑ ↑
RD
MONIT OR
CS Function ADDR MODE
2 08 3300 ST
↑ ↑ ↑ RD
2 08 3301 ST
↑ ↑ ↑ RD
2 08 3302 ST
↑ ↑ ↑ RD
2 08 3303 ST
↑ ↑ ↑
RD
2 08 3304 ST
↑ ↑ ↑
RD
2 08 3305 ST
↑ ↑ ↑ RD
2 08 3306 ST
↑ ↑ ↑ RD
2 08 3307 ST
↑ ↑ ↑ RD
2 08 3308 ST
↑ ↑ ↑
RD
2 08 3309 ST
↑ ↑ ↑ RD
2 08 330A ST
↑ ↑ ↑ RD
2 08 330B ST
↑ ↑ ↑ RD
3-10
ZR70 MC A, ZR65 MC A, ZR60 A
Microcomputer operation
DT
--
--
-- Completion of cleaning mode setup
Resetting of cleaning mode
Microcomputer operation
DT
--
-- WB is set.
--
-- WB is locked.
--
-- WB high-speed setting mode
--
-- WB outdoor mode
--
-- WB indoor mode
--
-- T he iris is opened forcibly.
--
-- T he iris is closed forcibly.
--
-- A value of AGC gain is maximized.
--
-- A value of AGC gain is minimized.
--
-- Outputs color bar from MACS.
--
-- Outputs white 100% from MACS.
--
-- Outputs white 50% from MACS.