FeiYu Tech MiNi 3D Manual

!
WARNING ! WARNING !
1. GoPro camera must be installed
before supplying power to the
Gimbal. Failure to do so will
result in damage to the gimbal
motors.
2. Be sure to connect the computer
with the USB Connector.
!
注意 !
1. 请先安装好Gopro相机后再通电 !
USB转换头
2. 连接电脑时请务必使用
2
Install 安装步骤
Install the damping ball to the
Ⅰ
adapter (up), then install the
adapter (up) to the aircraft. Please
according to the needing to use the
"V" hanger.
将云台减震球一端装入上挂版，并将上
挂版安装至飞机上，可根据需要使用V
型挂架
1
1 2
Adapter
( Up )
上挂板
3
Install 安装方式

Vertical Installation Diagram

立式安装方式示意图
Inverted Installation Diagram
悬挂安装方式示意图
MiNi 3D 3-Axis Brushless Gimbal For Aircraft
Suitable For Gopro4 / Gopro3+ / Gopro3 or the cameras with the similar size
MiNi3D 三轴无刷机载云台（适用于Gopro4 / Gopro3+ / Gopro3 或其它尺寸相近的运动摄像机)
1
Introduction 介绍
MiNi 3D 3-Axis Brushless Gimbal ( For aircraft ) suitable for GoPro4,GoPro3+,GoPro3 or cameras with similar size. Can be easily
mounted in fixed wing, multirotor, helicopter for aerial photography, and can work independently only need power supply.
You can assemble the gimbal properly according to the drawing, and then install the video camera on it.
There is no need to set up and adjust the parameter. For the first use, power on the Gimbal, and then keep it static for a while,
after its reset, the gimbal will be in a level position automatically. Then you can use it normally.
MiNi 3D 三轴无刷机载云台适用于Gopro4 / Gopro3+ / Gopro3 运动相机或其它尺寸相近的运动摄像机。可安装至固定翼飞机、多轴飞
行器、直升机上航拍。安装简单方便，只需连接电源便可以独立工作。
按照安装方式示意图准确地组装云台，注意先把摄像机安装到云台上再通电。
首次使用，接通云台电源，保持云台静止，等待云台初始化完成后自动将云台回到水平位置，即可正常使用，无需设置和调整参数。
Please install the adapter (down)
Ⅱ
to the heading motor, refer to the
following diagram.
将云台下挂板安装至下图电机两侧
4
3
3 4
Adapter
( Down )
Hexagonal Socket Head Cap Screw
Damping Ball
下挂板
内六角圆杯螺丝
减 震 球

Gimbal Connection Diagram

云台连接线路图
Install "V" Hanger
安装V形挂架
Install the part which assemble in step Ⅱ
Ⅲ
to the damping ball.
将第一步骤安装好的部件用减震球另一端按下图
装入至第二步骤安装好的部件中
2
2
5
M2×5mm
Knurled Thumb Screw
手拧螺钉
Adapter
(Down)
下挂板
Forward Installation Diagram
前置安装方式示意图
5
1
3
END
Optional
可 选
M2×25mm
Hexagonal Socket Head Cap Screw
内六角圆杯螺丝
Heading Control
航向控制
Pitch Control
俯仰控制
Mode Switch
模式切换
Video Output
视频输出
Power Connection
电源连接
Video Input Port
视频输入端口
Manual Version 1.0
Install the camera
Ⅳ
安装相机
M2.5×5mm
V Hanger
V型挂架
RC Receiver
RC 接收机