FeiYu Tech MINI 3D Pro Manual

!
WARNING ! WARNING !
1. GoPro camera must be installed before
supplying power to the Gimbal.
Failure to do so will result in damage to
the gimbal motors.
2. Make sure that the connection to the
computer is done by the
USB Connector
.
!
注 意 !
1. 请先安装好Gopro相机后再通电 !
USB转换头
2. 连接电脑时请务必使用
2
Install Step 安装步骤
Install the damping ball to the
Ⅰ
adapter (Up), then install the
adapter (up) to the aircraft. V hanger
is optional part to use if necessary.
将云台减震球一端装入上挂板，并将上挂板
安装至飞机上，可根据需要使用V型挂架
1
4
1
Adapter
( Up )
上挂板
3
Install Mode 安装方式
Inverted Installation Diagram
悬挂安装方式示意图
Default
默认安装方式
Vertical Installation Diagram
立式安装方式示意图
A
Mode A
Within the Inverted
Installation mode,
remove the camera
if needed, the motor
of Tilting axis rotating
180 degrees, then
方式A：
install the camera.
在默认悬挂安装方式下取
The install impression
下相机 ，将俯仰轴电机
drawing please refer
旋转180度后安装相机。
to the picture A.
安装完毕后如上图所示。
MiNi 3D Pro 3-Axis Brushless Gimbal For Aircraft
Suitable For Gopro4 / Gopro3+ / Gopro3 or the cameras with the similar size
MiNi3D Pro 三轴无刷机载云台（适用于Gopro4 / Gopro3+ / Gopro3 或其它尺寸相近的运动摄像机)
1
Introduction 介绍
MiNi 3D Pro 3-Axis Brushless Gimbal ( For aircraft ) suitable for GoPro4,GoPro3+,GoPro3 or cameras with similar size.
Can be easily mounted in fixed wing, multirotor, helicopter for aerial photography, and can work independently only
needed power supply.
You can assemble the gimbal properly according to the drawing, and then install the video camera on it.
There is no need to set up and adjust the parameter. For the first use, power on the Gimbal, and then keep it static for a
while, after its reseting, the gimbal will be in a level position automatically. Then you can use it normally.
MiNi 3D Pro 三轴无刷机载云台适用于Gopro4 / Gopro3+ / Gopro3 运动相机或其它尺寸相近的运动摄像机。可安装至固定翼飞机、
多轴飞行器、直升机上航拍。安装简单方便，只需连接电源便可以独立工作。
按照安装方式示意图准确地组装云台，注意先把摄像机安装到云台上再通电。
首次使用，接通云台电源，保持云台静止，等待云台初始化完成后自动将云台回到水平位置，即可正常使用，无需设置和调整参数。
Install the damping ball to the Adapter(Down).
Ⅱ
将减震球另一端按下图装入至云台下挂板中
2
2
Damping Ball
减 震 球
Gimbal Connection Diagram
云台连接线路图
Install "V" Hanger
安装V形挂架
B
方式B：
在默认的悬挂安装方式中使
用遥控器连续6次进入航向
跟随模式，则立即关闭电机，
重新上电后将以上图所示的
立式方式工作。再次连续6
次进入航向跟随模式可切换
回悬挂安装模式
1
2
3 4
Knurled Thumb Screw
Screw (Not Included）
手拧螺钉
M2×25mm
螺丝 (自备）
Mode B
Within the Inverted Installation mode，Switch
to the "Panning mode" 6 times in
succession, the gimbal will be switched to
"Vertical installation" and stop the motor.
Remove the power and install to the correct
installation mode then power on to work
normally. The install impression drawing please
refer to the picture B .
If want to back to Vertical Installation mode
please operate again: switch to the
"Panning mode" 6 times in
succession for switching.
Install the camera
Ⅲ
安装相机
3
END
V Hanger
V型挂架
M2.5×5mm
Hexagonal Socket Head Cap Screw
内六角圆杯螺丝
Video Output And
Camera Charging Cable
相机视频/充电线
Power Cable 电源线
Video Output
视频输出
This interface can be output 5 voltage and
input analog video signal of GoPro camera
此端口可输出5V电压及接入GoPro模拟视频信号
Mode Switch
模式切换
Tilting Control
俯仰控制
Panning Control
航向控制
Note: RC receiver needs to be
注意：接收机需单独供电
Forward Installation Diagram
前置安装方式示意图
Manual Version 1.0
V Hanger
V型挂架
5V
Video
Control
Video
GND
powered separately