Calibrating The Pedal - Korg Grandstage 88 Owner's Manual

Volume This is used to control the volume.
(CC#7) Controls the volume on the output line for both
the KEYBOARDS and ENSEMBLE sections. (*1)
Master Controls the master volume.
Volume This controls the volume at the last stage of
the sound generator output. At the same time,
this sends a master volume message (universal
exclusive message) to control the volume of all
outputs, including the REVERB/DELAY section
and the equalizer. (*3)
M. Wheel This allows the modulation wheel effect of the
(CC#1) Grandstage to be controlled by pedal.
MIDI Outputs the MIDI control change message that
CC#0... is set. If the Grandstage supports this control
#95 setting, the effect will be applied.
MIDI Outputs the MIDI control change message that
CC#102... is set. If the Grandstage supports this control
#119 setting, the effect will be applied.
*1: Controls the volume of the REVERB/DELAY section and
the equalizer prior to input.
*2: On the CX-3 type organ programs, this controls the volume
before the rotary speaker input. Recreates the effect of an
expression pedal used with drawbar organs. The expression
pedal effect can be recreated in the same way for VOX organ
and electric organ programs as well.
*3: The MASTER VOLUME knob adjusts the output level from
AUDIO OUTPUT.
Foot - Switch (foot switch functions)
This sets the functions that will be controlled when a foot pedal
(such as the PS-1 or PS-3, sold separately) is connected to the
FOOT CONTROLLERS SWITCH jack on the rear panel. This
allows you to switch between favorites, as well as control sounds
and effects.
The default setting is "SW2 (CC#81)".
Function Details
Off The connected pedal will not function.
SW 1 This controls the SW1 button effect using a foot
(CC#80) switch.
SW 2 This controls the SW2 button effect using a foot
(CC#81) switch.
Soft Turns the soft pedal effect on or off.
(CC#67)
Favorite Selects the next favorite number using a foot
Up switch. At the same time, this sends a program
change message.
Favorite Selects the previous favorite number using
Down a foot switch. At the same time, this sends a
program change message.
MIDI Outputs the MIDI control change message that
CC#0... is set. If the Grandstage supports this control
#95 setting, the effect will be applied.
MIDI Outputs the MIDI control change message that
CC#102... is set. If the Grandstage supports this control
#119 setting, the effect will be applied.

Calibrating the pedal

Damper Calib. (damper pedal calibration)
Calibrate the damper pedal (such as the DS-1H) that is connected
to the DAMPER jack. This will adjust the half-damper variable
range.
Tip:
The calibration set here will be stored in memory until you
perform the calibration again.
1. Connect the damper pedal to the Grandstage.
Refer to "FOOT CONTROLLERS" on page 10 for how to
connect the pedal.
2. Lift your foot off the damper pedal.
3. Press the SYSTEM button, and select "Damper
Calib." using the VARIATION knob.
"[Press Pedal]" will blink on the third line of the display.
Note:
If you wish to cancel the calibration while
"[Press Pedal]" is blinking, select a parameter using
the VARIATION knob, or press the SYSTEM or
EXIT button to finish system settings.
4. Press the damper pedal down all the way until it
stops, and then lift your foot off the pedal.
Note:
The display will stop blinking and remain lit while
the damper pedal is being used. If nothing happens
even when you press the pedal, the pedal may not
be connected properly to the DAMPER jack. Check
the connections.
5. When the calibration is completed, the word
"Completed" will be shown on the third line of
the display.
Note:
If calibration was not correctly completed,
"[Press Pedal]" will blink. Do step 4 once more.
6. To continue making other settings, use the
VARIATION knob to select the necessary
parameter.
Foot Sw Calib. (foot switch calibration)
Calibrate the switch-type foot pedal (such as the PS-1 or PS-3,
sold separately) that is connected to the SWITCH jack. This will
adjust the pedal's variable range.
Tip:
The calibration set here will be stored in memory until you
perform the calibration again.
1. Connect the switch-type foot pedal to the
Grandstage.
Refer to "FOOT CONTROLLERS" on page 10 for how to
connect the pedal.
2. Lift your foot off the foot pedal.
3. Press the SYSTEM button, and select "Foot Sw
Calib." using the VARIATION knob.
"[Press Pedal]" will blink on the third line of the display.
Note:
If you wish to cancel the calibration while
"[Press Pedal]" is blinking, select a parameter using
the VARIATION knob, or press the SYSTEM or
EXIT button to finish system settings.
4. Press the foot pedal down all the way until it
stops, and then lift your foot off the pedal.
Note:
The display will stop blinking and remain lit while
the foot pedal is being used. If nothing happens
even when you press the pedal, the pedal may not
be connected properly to the SWITCH jack. Check
the connections.
17