Table of Contents
Advertisement
EPC-3221 CompactPCI
System Controller Board and C1XTN02 Transition I/O Module
®
Advanced
The options for the Advanced menu are listed in the following table:
Option / Sub-Menu
ª
I/O Device
Serial Port A
Configuration /
Integrated Peripherals
Serial Port A: Base I/O Address/
IRQ
Serial Port B
Serial Port B: Base I/O Address/
IRQ
Serial Port B: Mode
Parallel Port
Parallel Port: Mode
Parallel Port: Base I/O Address
Parallel Port: Interrupt
Parallel Port: DMA Channel
Floppy Disk Controller
Floppy Disk Controller:
Base I/O Address
Local Bus IDE Adapter
ª
Advanced Chipset
ECC Configuration
Control
Watchdog Timer Status
Watchdog Timer Delay
Note: For more information on the Watchdog Timer, see
Thermal Duty Cycle
ª
PCI Configuration
PCI IRQ Line 1 – 4
USB IRQ Enable
Latency Timer
Cache Line Size
PCI/PNP ISA UMB Region
Exclusion:
C800–CBFF, CC00–CFFF,
D000–D3FF, D400–D7FF,
D800–DBFF, DC00–DFFF
PCI/PNP ISA IRQ Resource
Exclusion:
IRQ 3, IRQ4, IRQ5, IRQ7,
IRQ9, IRQ10, IRQ11, IRQ12
Embedded PCI Devices:
AGP VGA
Embedded PCI Devices:
Ethernet
Embedded PCI Devices:
Ethernet Port
Embedded PCI Devices:
Adaptec Ultra-2 SCSI Adapter
24
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Item
Default Setting
Enabled (user configuration)
Note: Base I/O Address and Interrupt are displayed / shown only if the
Serial Port is Enabled.
Note: For console redirection, select Enabled.
Note: If user wishes to use this port for Console Redirection, select
Enabled and set the I/O Address IRQ appropriately
3F8/IRQ4
Enabled
Note: Base I/O Address and Interrupt are displayed / shown only if the
Serial Port is Enabled.
Note: For console redirection, select Enabled.
Note: If user wishes to use this port for Console Redirection, select
Enabled and set the I/O Address IRQ appropriately
2F8/IRQ3
Normal
Enabled
Note: Mode, Base I/O Address, and Interrupt are displayed / shown only
if the Parallel Port is Enabled.
Bi-Directional
Note: If Mode is set to ECP, a DMA channel must be set.
378
IRQ 7
DMA 1
Note: This option is displayed / shown only if Mode is set to ECP.
Enabled
Primary
Both
EC
Disabled
1.2 sec
37.5%
Auto Select (all IRQ lines)
Yes
Note: The USB controller uses PCI IRQ line 4 (INTD).
Auto (64)
Auto (8)
Available (all regions)
Available (all IRQs)
Enabled
Note: The video controller uses PCI IRQ line 1 (INTA).
Disabled
Note: The ethernet controller uses PCI IRQ line 1 (INTA).
Front Panel
Disabled
Note: The SCSI controller uses PCI IRQ line 4 (INTD). The SCB will only
support SE Ultra SCSI, not LVD Ultra-2 SCSI.
Alternate Settings
Disabled, Auto
2F8/IRQ3, 3E8/IRQ4,
2E8/IRQ3
Disabled, Auto
3F8/IRQ4, 2F8/IRQ3,
3E8/IRQ4
Modem
Disabled, Auto
Output Only (ISA), EPP, ECP
278, 3BC
IRQ 5
DMA 3
Disabled
Secondary
Disabled, Primary, Secondary
ECC, ECC Scrub, Disabled
Enabled
150 ms
page
43.
12.5%, 25%, 50%, 62.5%, 75%, 87.5%
Disabled, 3 (COM2/COM4),
4 (COM1/COM3), 5 (2nd LPT),
7 (1st LPT), 9 (Open), 10 (Open),
11 (Open), 12 (PS/2 Mouse),
14 (Primary IDE), 15 (Secondary IDE)
No
32, 96, 128, 160, 192, 224
8, 12, 16, 20, 24, 28, 32, 36, 40, 44, 48,
52, 56, 60
Reserved
Reserved
Disabled
Enabled
Chassis Panel
Enabled
Service Manual
Advertisement
Table of Contents
