How should I prepare the structure for installing a MAAX Vivez Series shower base?

To prepare the structure for your MAAX Vivez Series shower base, you need to build a structure based on the dimensions provided in the chart. If a structure is already built, verify that its dimensions respect those in the chart. Also, verify that the walls are square and the floor is perfectly level. An approximate 6" x 6" opening should be cut around the drain center using dimensions C and D from the chart. For more information, see page 5 of the manual.

How do I install the MAAX Vivez Series shower base?

The installation of the MAAX Vivez Series shower base involves several steps. First, remove the clear plastic film from around the drain hole and threshold. Then, apply silicone around the edge of the drain hole and assemble the drain. Install the base by pushing it completely against the back studs and centering it. Verify the base leveling, inserting wood shims as needed. Place cement or wood shims under all legs to support the base. Finally, drill holes in the base flange and secure it to the wall studs with screws, filling holes with silicone before screwing.

What tools are required for MAAX Vivez Series shower base installation?

The MAAX Vivez Series shower base installation requires specific tools including a 24" level min., pencil, electric drill with 1/8" drill bits, utility knife, 18" square min., safety equipment, screwdriver, and measuring tape. For more information, see page 3 of the manual.

What supplies are needed for MAAX Vivez Series shower base installation?

For the MAAX Vivez Series shower base installation, you will need supplies such as clear silicone sealant, a box of #8x1¾" flathead screws, wood shims, self-leveling cement, cement, and a shower drain (which is required for Distinct shower bases and included with Zone Square bases). For more information, see page 3 of the manual.

How do I ensure the floor is level before installing a MAAX Vivez Series shower base?

Leveling the floor is critical for a properly aligned installation. Auto leveling cement can be used to level the floor, but be careful not to block the drain hole position. For more information, see page 5 of the manual.

How do I secure the MAAX Vivez Series shower base to the wall studs?

To secure the MAAX Vivez Series shower base to the wall studs, drill holes in the base flange with a 1/8" drill bit (pre-drilling the flange only, not the studs). Then, secure the base to all wall studs using #8 x 1¾" flat-head screws. The bottom of all holes in the flange must be at least 8mm (3/8") above the base threshold, and holes must be filled with silicone before screwing. For more information, see page 9 of the manual.

What are the dimensions for the MAAX Vivez Series shower base structure?

The dimensions for the MAAX Vivez Series shower base structure vary by model. For specific measurements (A, B, C, D), refer to the chart under "STEP 1 Building the structure; drain position". For example, the Distinct 4832 base has dimensions A: 48" - 48 1/4", B: 32", C: 4 1/2", D: 24".

How do I connect the drain pipe for the MAAX Vivez Series shower base?

It is recommended that a plumber completes the drain pipe connection for the MAAX Vivez Series shower base.

What should I do if I have a U tile wall system with my MAAX Vivez Series shower base?

If you are installing a MAAX Vivez Series shower base with a U tile wall system, DO NOT USE these instructions. Instead, use only the instructions found inside the U tile back wall box. For more information, see page 1 of the manual.

How do I use shims to level and position the MAAX Vivez Series shower base?

To level the MAAX Vivez Series shower base, insert wood shims on the floor around the outline of the base on previously marked spots to compensate for leveling. You may also need to place cement or wood shims under all legs. If necessary, use wood shims between the studs and the tiling flange to maintain the centered position of the base.

What parts are included with the MAAX Vivez Series shower base?

The MAAX Vivez Series shower base typically includes the Base. For the Distinct base, a drain cover is included. For the Zone Square base, a drain is included. For more information, see page 4 of the manual.

How do I install the drain cover for the MAAX Vivez Series Distinct 48 shower base?

To install the drain cover for the MAAX Vivez Series Distinct 48 shower base, simply insert the drain cover (3) as shown.

MAAX Vivez Series Installation Instructions Manual

Shower base

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Read all instructions carefully before proceeding.

Lire toutes les instructions attentivement avant de commencer

l'installation.

Leer detenidamente todas las instrucciones antes de comenzar

la instalación.

IMPORTANT

• Record the serial number

IMPORTANT

• Noter le numéro de série

IMPORTANTE

• Registre el número de serie

DISTINCT & ZONE SQUARE SHOWER BASE INSTALLATION

INSTALLATION BASE DE DOUCHE DISTINCT & ZONE SQUARE

INSTALACIÓN DE BASE DE DUCHA DISTINCT & ZONE SQUARE

SAVE THIS GUIDE FOR FUTURE REFERENCE.

CONSERVER POUR UN USAGE ULTÉRIEUR.

CONSERVE ESTE MANUAL COMO REFERENCIA.

INSTALLATION INSTRUCTIONS

GUIDE D'INSTALLATION

GUÍA DE INSTALACIÓN

Serial number • Numéro de série • Número de Serie

Table of Contents

How should I prepare the structure for installing a MAAX Vivez Series shower base?

To prepare the structure for your MAAX Vivez Series shower base, you need to build a structure based on the dimensions provided in the chart. If a structure is already built, verify that its dimensions respect those in the chart. Also, verify that the walls are square and the floor is perfectly level. An approximate 6" x 6" opening should be cut around the drain center using dimensions C and D from the chart.

For more information, see page 5 of the manual.

Was this helpful?
How do I install the MAAX Vivez Series shower base?

The installation of the MAAX Vivez Series shower base involves several steps. First, remove the clear plastic film from around the drain hole and threshold. Then, apply silicone around the edge of the drain hole and assemble the drain. Install the base by pushing it completely against the back studs and centering it. Verify the base leveling, inserting wood shims as needed. Place cement or wood shims under all legs to support the base. Finally, drill holes in the base flange and secure it to the wall studs with screws, filling holes with silicone before screwing.

Was this helpful?
What tools are required for MAAX Vivez Series shower base installation?

The MAAX Vivez Series shower base installation requires specific tools including a 24" level min., pencil, electric drill with 1/8" drill bits, utility knife, 18" square min., safety equipment, screwdriver, and measuring tape.

For more information, see page 3 of the manual.

Was this helpful?
What supplies are needed for MAAX Vivez Series shower base installation?

For the MAAX Vivez Series shower base installation, you will need supplies such as clear silicone sealant, a box of #8x1¾" flathead screws, wood shims, self-leveling cement, cement, and a shower drain (which is required for Distinct shower bases and included with Zone Square bases).

For more information, see page 3 of the manual.

Was this helpful?
How do I ensure the floor is level before installing a MAAX Vivez Series shower base?

Leveling the floor is critical for a properly aligned installation. Auto leveling cement can be used to level the floor, but be careful not to block the drain hole position.

For more information, see page 5 of the manual.

Was this helpful?
How do I secure the MAAX Vivez Series shower base to the wall studs?

To secure the MAAX Vivez Series shower base to the wall studs, drill holes in the base flange with a 1/8" drill bit (pre-drilling the flange only, not the studs). Then, secure the base to all wall studs using #8 x 1¾" flat-head screws. The bottom of all holes in the flange must be at least 8mm (3/8") above the base threshold, and holes must be filled with silicone before screwing.

For more information, see page 9 of the manual.

Was this helpful?
What are the dimensions for the MAAX Vivez Series shower base structure?

The dimensions for the MAAX Vivez Series shower base structure vary by model. For specific measurements (A, B, C, D), refer to the chart under "STEP 1 Building the structure; drain position". For example, the Distinct 4832 base has dimensions A: 48" - 48 1/4", B: 32", C: 4 1/2", D: 24".

Was this helpful?
How do I connect the drain pipe for the MAAX Vivez Series shower base?

It is recommended that a plumber completes the drain pipe connection for the MAAX Vivez Series shower base.

Was this helpful?
What should I do if I have a U tile wall system with my MAAX Vivez Series shower base?

If you are installing a MAAX Vivez Series shower base with a U tile wall system, DO NOT USE these instructions. Instead, use only the instructions found inside the U tile back wall box.

For more information, see page 1 of the manual.

Was this helpful?
How do I use shims to level and position the MAAX Vivez Series shower base?

To level the MAAX Vivez Series shower base, insert wood shims on the floor around the outline of the base on previously marked spots to compensate for leveling. You may also need to place cement or wood shims under all legs. If necessary, use wood shims between the studs and the tiling flange to maintain the centered position of the base.

Was this helpful?
What parts are included with the MAAX Vivez Series shower base?

The MAAX Vivez Series shower base typically includes the Base. For the Distinct base, a drain cover is included. For the Zone Square base, a drain is included.

For more information, see page 4 of the manual.

Was this helpful?
How do I install the drain cover for the MAAX Vivez Series Distinct 48 shower base?

To install the drain cover for the MAAX Vivez Series Distinct 48 shower base, simply insert the drain cover (3) as shown.

Was this helpful?

Need help?

Do you have a question about the Vivez Series and is the answer not in the manual?

Questions and answers

Summary of Contents for MAAX Vivez Series

Page 1 INSTALLATION INSTRUCTIONS GUIDE D’INSTALLATION GUÍA DE INSTALACIÓN DISTINCT & ZONE SQUARE SHOWER BASE INSTALLATION INSTALLATION BASE DE DOUCHE DISTINCT & ZONE SQUARE INSTALACIÓN DE BASE DE DUCHA DISTINCT & ZONE SQUARE Read all instructions carefully before proceeding. SAVE THIS GUIDE FOR FUTURE REFERENCE. CONSERVER POUR UN USAGE ULTÉRIEUR.
Page 2: Table Of Contents
Table of contents: Page Tools and supplies......................3 Parts and components......................4 1. Building the structure..................... 5 2. Installing the base......................6 3. Finish..........................10 4. Maintenance........................11 5. Warranty.......................... 12 Table de matières: Page Outils et matériaux......................3 Pièces et composantes.......................4 1.
Page 3: Tools And Supplies
TOOLS OUTILS HERRAMIENTAS REQUIRED REQUIS NECESARIAS 1/8" drill bits Mèches de 1/8 Utility knife Couteau à lame 24" level min. Electric drill Pencil rétractable Niveau de 24po. min. Perçeuse électrique Crayon Cuchillo multiuso Nivel de 24" min. Taladro eléctrico Lápiz 18"...
Page 4: Parts And Components
PARTS PIÈCES PIEZAS ZONE SQUARE 48 & 60 DISTINCT 48 COMPONENTS COMPOSANTES COMPONENTES Part Nom de la pièce Pieza Qty / Qté / Cant. Code Base Base Base Drain cover (with Couvercle de drain linéaire (inclus Cubierta del desagüe (incluido 10037090 Distinct base only) avec la base Distinct seulement)
Page 5: Building The Structure
Follow all instructions and check them off as you go. Suivre toutes les instructions et les cocher lorsqu'elles sont terminées. Siga todas las instrucciones y marcarlas cuando estén terminadas. Building the structure; drain position STEP Construction de la structure; position du drain ÉTAPE Construcción de la estructura;...
Page 6: Installing The Base
Installing the base STEP Installation de la base ÉTAPE Remove the clear plastic film from around the drain hole Instalación de la base ETAPA and threshold before applying silicone. Keep the film on the base floor as protection until the installation is complete. Enlever la pellicule de plastique transparente autour du drain et sur le pourtour de la base avant de mettre le silicone.
Page 7 Installing the base (cont'd) STEP Installation de la base (suite) ÉTAPE Instalación de la base (cont.) ETAPA Verify the base leveling. Mark the studs and the floor Check me! where shims will be required to perfectly level the base. Cochez-moi! If the base is completely leveled go to step 2.5.
Page 8 Installing the base (cont'd) STEP Installation de la base (suite) ÉTAPE Instalación de la base (cont.) ETAPA Lift the base. Place cement or wood shims under all legs to support the Check me! shower base floor. Lower the shower base and validate leveling and stability Cochez-moi! of the base on the floor.
Page 9 Installing the base (cont'd) STEP Installation de la base (suite) ÉTAPE Instalación de la base (cont.) ETAPA Check me! Cochez-moi! With a 1/8" drill bit, drill holes in the base flange then Marcarme! secure the base to all the wall studs with #8 x 1¾" flat-head screws (not included).
Page 10: Finish
Finish STEP Finition ÉTAPE Acabado ETAPA Seal the joint between the unit and the wall covering Check me! with a bead of silicone. As shown, leave a 1" gap on the Cochez-moi! sides to work as a weep hole. Marcarme! Make sure to never obstruct the weep holes.
Page 11: Maintenance
ENTRETIEN MANTENIMIENTO MAINTENANCE La desinfección periódica es una excelente Regular disinfection provides an effective Une désinfection régulière constitue une defence against various types of bacteria excellente prévention contre les types de forma de prevenir la aparición de diferentes tipos de bacterias que suelen desarrollarse that can develop in deposits that build up bactéries susceptibles de se développer over time in all bathtubs and showers.
Page 12: Warranty
Sauf dans le cas des produits MAAX munis Salvo en el caso de productos de MAAX con Except in the case of MAAX products with d’accessoires pré-assemblés, MAAX en aucun cas accesorios de plomería pre-instalados, MAAX...

This manual is also suitable for:

Vivez distinct 4832 Vivez zone square 6032 Vivez zone square 4832

MAAX Vivez Series Installation Instructions Manual

Page Table of Contents:

Page Table de Matières: