Page 1
Installation- and user manual wallbe Pro – 3,7kW to 22kW English wallbe GmbH – Paderborner Str. 76 – 33189 Schlangen Tel: +49 5252 989440 Mail: inquiry@wallbe.de...
6.0 Installation .......................... 25 6.1.1 Wall mounting ......................25 6.2 Installation of the wallbe Pro charging pillar ..............26 6.2.1 Installation using the pre-built foundation incl. stainless steel mounting plate ..26 7.0 Usage of your wallbe Pro ....................27 7.1.1 Authorization via ON/OFF button ................
Page 3
The company behind wallbe.de: wallbe GmbH is a specialist for intelligent charging solutions (e.g. for parking structures with RFID, OCPP, energy logging). Data transfer via LAN or GSM and matching connections into existing IT-systems as well as solutions for charging infrastructure for electric vehicles in connection with load management systems and renewable energy (e.g.
Don´t try to repair or open the device yourself. Risk of electric shock might be possible! The installation, connection and initial start-up must be performed by trained personnel with corresponding abilities. wallbe GmbH – Paderborner Str. 76 – 33189 Schlangen Tel: +49 5252 989440 Mail: inquiry@wallbe.de...
Those packaging materials are raw materials and can be re-used or recycled. Please dispose this device in an ecologically responsible way by handing it over to a local collection depot for old devices. wallbe GmbH – Paderborner Str. 76 – 33189 Schlangen Tel: +49 5252 989440 Mail: inquiry@wallbe.de...
1. Be aware that you have to install an adequate LS-switch (see table) in the electrical sub distribution! 2. Be aware that your wallbe Eco 2.0 is already equipped with a DC residual current detection >6mA. Therefore a cost intensive RCD Type A (EV) or Type B in the switch board is not necessary.
Pro wallbe Pro (Input 3,7kW 4,6kW 7,4kW (Input terminal 11kW 22kW terminal X1) brown brown or black blue black green grey /yellow blue green /yellow wallbe GmbH – Paderborner Str. 76 – 33189 Schlangen Tel: +49 5252 989440 Mail: inquiry@wallbe.de...
10. Remove the Protection film from the adhesive tapes on your aluminum mounting frames and place them horizontally onto your wallbe Pro. Please make sure that that the mounting frame holes and wallbe Pro mounting holes are on top of each other.
Mount your wallbe Pro charging pillar onto the stainless steel mounting plate using the included screws. 10. Connect the supply line according to your wallbe Pro model. Please follow the instructions in chapter “5.1 Supply line connection”. wallbe GmbH – Paderborner Str. 76 – 33189 Schlangen...
7.1.1 Authorization via ON/OFF button 1. Connect the tethered charging cable of your wallbe Pro to your EV. If you own a wallbe Pro with a Type 2 socket, connect your charging cable to the wallbe Pro and then to your EV.
7.1.3 Authorization via RFID* 1. Connect the tethered charging cable of your wallbe Pro to your EV. If you own a wallbe Pro with a Type 2 socket, connect your charging cable to the wallbe Pro and then to your EV.
Please contact an electrician to check your subdistribution and power supply. Error case 3: You are not able to remove the charging cable from your car/wallbe Pro. 2. wallbe Pro – Tethered cable: In some cases the locking mechanism remains active to prevent removal by unauthorized personnel.
Store the charging cable with the Protective cap on it at a dry and clean place. Alternatively you can store the vehicle connector in the parking position of your wallbe Pro if you have ordered it with a tethered charging cable.
Page 15
Our wallbe charging stations come with a 2 year manufacturer warranty. Every single wallbe is shipped with a warranty card in two duplicates, where one is intended for the end customer and the other one for the manufacturer. Please make sure that you fill all the fields with the necessary information on the warranty card and submit the warranty card via E-Mail, mail or Fax.