Page 1
Nortel CallPilot 201i Server Hardware Installation ATTENTION Clicking on a PDF hyperlink takes you to the appropriate page. If necessary, scroll up or down the page to see the beginning of the referenced section. NN44200-301...
Page 2
The process of transmitting data and call messaging between the CallPilot server and the switch or system is proprietary to Nortel Networks. Any other use of the data and the transmission process is a violation of the user license unless specifically authorized in writing by Nortel Networks prior to such use. Violations of the license by alternative usage of any portion of this process or the related hardware constitutes grounds for an immediate termination of the license and Nortel Networks reserves the right to seek all allowable remedies for such breach.
Page 3
QUICKTIME is a trademark of Apple Computer, Inc. RADISYS is a trademark of Radisys Corporation. ROLM is a trademark of Siemens ROLM Communications Inc. SLR4, SLR5, and TANDBERG are trademarks of Tandberg Data ASA. SONY is a trademark of Sony Corporation. SYBASE is a trademark of Sybase, Inc.
Page 8
Installing the MPCs 102 Installing the monitor, keyboard, and mouse 104 Connecting the CD-ROM and tape drives 105 Connecting the 201i server to the switch, ELAN subnet , and Nortel server subnet 113 Connecting the modem 116 Completing the installation 118...
Getting help over the phone from a Nortel Solutions Center If you don’t find the information you require on the Nortel Technical Support Web site, and have a Nortel support contract, you can also get help over the phone from a Nortel Solutions Center.
Page 10
To access some Nortel Technical Solutions Centers, you can use an Express Routing Code (ERC) to quickly route your call to a specialist in your Nortel product or service. To locate the ERC for your product or service, go to: http://www.nortel.com/erc...
Introduction The 201i server is a flexible multimedia telephony server designed to integrate with Nortel Meridian 1* and Communication Server* 1000 products. The 201i server occupies two slots of a Meridian 1 shelf or Communication Server 1000 Media Gateway or Media Gateway Expansion. When the server is locked into position, its connectors attach to the backplane, which provides power and communications links.
Page 13
Two Ethernet controllers on the 201i server motherboard provide Ethernet capability. These controllers provide the network interfaces for both the ELAN subnet and the Nortel server subnet. The connections to these subnets are established by using the multi I/O cable described on "Multi I/O...
Page 20
Note: For more information about the ELAN subnet, see the CallPilot Installation and Configuration Task List. You use the 201i server multi I/O cable to establish the connections to the ELAN subnet and the Nortel server subnet. For more information, see "Multi I/O cable description" (page 21).
Page 25
Note: The mouse connector on the 201i faceplate is a PS/2 connector. If you plan to use a USB mouse with USB-to-PS/2 converter, you must also use the Nortel-supplied 101 mm (4-in) PS/2 extension cable (A0855616). Without the extension cable, the monitor connector partially blocks the mouse connector.
Page 30
Connect the multi I/O cable to the ELAN and CLAN Ethernet hubs or switches (see "Connecting the 201i server to the switch, ELAN subnet , and Nortel server subnet" (page 113)). Note: If more than 3 m (10 ft) of multi I/O cable is required, use the supplied RJ-45 female-to-female gender change jacks to attach additional cable.
See 201i server components diagram on page 15. What to do if components are missing or damaged THEN you observe any damage contact your Nortel technical support representative. components have become loose secure them. If necessary, refer to the procedures in the CallPilot <server model>...
Page 35
The ELAN subnet and the Nortel server subnet must be configured and the appropriate networking equipment must be available. If the Nortel server subnet is to be part of the customer LAN, you need a network specialist to ensure proper configuration.
Page 38
Backplane (tip and ring) cable The backplane (tip and ring) cable supplied with the 201i server (NTRH3501) provides 100Base-T Ethernet operation for the Nortel server subnet. This cable offers more network throughput than the cable that is already installed on the Meridian 1.
Introduction You must connect the backplane (tip and ring) cable supplied with the 201i server (NTRH3501) for 100Base-T Ethernet operation to the Nortel server subnet. This cable offers more network throughput than the cable you just removed from the Meridian 1.
Page 72
100Base-T connectors for connecting Media Gateways using one of the following: — for connections over the LAN customer-supplied standard 100Base-T CAT5 Ethernet cables — for point-to-point connections (Nortel-supplied crossover Ethernet cables) • one 10Base-T Ethernet connector that — provides the ELAN subnet interface to management software applications, such as Optivity Telephony Manager and CallPilot —...
Page 73
201i server in a pair of consecutive slots in the Media Gateway or Media Gateway Expansion. The following table identifies the Media Gateway and Media Gateway Expansion slots into which you can install the CallPilot 201i server: The 201i server Unit...
Page 76
Action WARNING Risk of eye injury Nortel recommends that you operate the Media Gateway and Media Gateway Expansion with their front bezels installed. When the blue LEDs inside these units are lit, they are very bright. Remove the front bezel from the Media Gateway or Media Gateway Expansion as shown in the diagram on the next page.
Before you begin Determine which pair of consecutive slots are to contain the 201i server. The following table identifies the Media Gateway and Media Gateway Expansion slots into which the CallPilot 201i server can be installed: The 201i server Unit...
Action WARNING Risk of eye injury Nortel recommends that you operate the Media Gateway and Media Gateway Expansion with their front bezels installed. When the blue LEDs inside these units are lit, they are very bright. Align the two posts and the locking tab on the rear of the front bezel with the slots on the inside front cover plate.
The first device in a SCSI device daisy chain can be either the tape drive or the CD-ROM drive. However, because the Tandberg SLR5 tape drive is already internally terminated at the factory, Nortel recommends that you connect the tape drive as the last device.
"Installing the MPCs" (page 102) "Installing the monitor, keyboard, and mouse" (page 104) "Connecting the CD-ROM and tape drives" (page 105) "Connecting the 201i server to the switch, ELAN subnet , and Nortel server subnet" (page 113) "Connecting the modem" (page 116) "Completing the installation"...
The modem must be connected to the 201i server if: • you want to administer the 201i server from a remote location that does not have access to the Nortel server subnet. • you need assistance from Nortel technical support.
Once you have successfully started and configured the 201i server, remove the monitor, keyboard, and mouse. For day-to-day administration, use a web browser on a PC that is connected to the ELAN subnet or Nortel server subnet. Hardware requirement CAUTION Risk of equipment damage The mouse connector on the 201i faceplate is a PS/2 connector.
Connecting the 201i server to the switch, ELAN subnet , and Nortel server subnet 113 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide. If you want to use a connection scenario that is not described in this guide, ensure that you use appropriate cabling for each SCSI device.
Connecting the 201i server to the switch, ELAN subnet , and Nortel server subnet 115 • Option 11C Mini or Communication Server 1000 to a screw on the back of the cabinet Nortel CallPilot 201i Server Hardware Installation NN44200-301 01.01 Standard 5.0 15 February 2007...
Connect the connector on the multi I/O cable that is labeled as ELAN to the switch network hub or switch. If Nortel server subnet is required, connect the connector on the multi I/O cable that is labeled as CLAN to the CLAN 10- or 100Base-T-compliant network hub or switch.
To complete the installation of the 201i server, lock the 201i into position. The server starts up automatically. ATTENTION When connecting the optional Nortel server subnet, do not power up unless your antivirus programs and Nortel security updates are installed first. To complete the installation and start the 201i server Note: Ensure that the switch in which the 201i is installed is powered on.
Document version: 01.01 Document date: 15 February 2007 To provide feedback or report a problem in this document, go to www.nortel.com/documentfeedback. Sourced in Canada The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty.