Table of Contents
Advertisement
IFC130-P_EN
5/08/05
9:48
Getting started
Remote control TV functions
Most of your television's functions are available via the menus that
appear on the screen.The remote control supplied with your set
can be used to navigate through the menus and to configure all the
general settings.The remote control and its functions may vary
depending on the model of television.You will find on this page the
description of the most comprehensive remote control. Optional
remote control features are indicated by the symbol
EN
Standby / quit standby.
TV To access TV mode. Press this button to control the
television.
VCR To access VCR mode.
DVD To access DVD mode.
SAT To access SAT mode.
AUX To access AUX mode.
AMP To access AMP mode.
light To provide information:
- it lights up when you press a button,
- it indicates the status when the remote control is being
programmed (see further below),
- if the batteries are run down, it flashes when you press a
button.
PRESETS (red button) preset settings menu.
Zzz/LIST (green button) list of channels (see page 9).
INFO (yellow button) status information (see page 8).
GUIDE (blue button) programme information (see page 8).
TEXT (purple button) Teletext (see page 19).
The coloured buttons can also be used for operating Teletext.
To select menu options.
To set functions, change values, enable and disable
functions (checkbox) in menus.
To select the picture format or zoom.
OK To confirm a selection, enable and disable functions
(checkbox) in menus.
To freeze the picture (see page 9).
MENU To access the
EXIT To exit the menu structure.
+/- To control the volume.
or
To switch the sound off and back on again.
RETURN To return to the previous channel/AV programme.
PR+/PR- To change channels.
0-9 To select a channel by its number. In the case of channel
numbers with two digits:
- press the tens digit for a few seconds to display it on the
screen, then press the units digit or
- press
0/--
To enter numeric values in menus.
In PC mode, the buttons
mode and change channels.
AV To select an appliance connected to an AV socket.
DEMO (Disabled).
Page 4
.
OVERVIEW
menu.
--
to display "
", then enter the channel number.
1-9
can be used to return to TV
Playing files from memory cards
When playing mp3,WMA, JPEG, MPEG and DivX files, you can use
some of the buttons on the remote control to perform certain
functions, which vary according to the type of file.
INFO To display the Info menu.
REV mp3 and WMA: to return to the previous file.
JPEG: to reduce the projection speed.
PLAY To play.
FWD mp3 and WMA: to go on to the next file.
JPEG: to increase the projection speed.
STOP To stop playing.
PAUSE To pause, stop at a particular picture.
MPEG and DivX: to change files.
0-9 MPEG and DivX: to select a file by its number.
Using the remote control for other
equipment
This remote control can be used to control other appliances using
the programmable buttons
VCR
AUX
. For each button you can control the following
appliances:
VCR
: video recorder
DVD
: DVD player
SAT
: satellite receiver, cable network
AMP
: hi-fi system, Home Cinema amplifier
AUX
: decoder for terrestrial digital TV set and any other
appliance. For instance, if you have two video recorders, you can
program the
VCR
button to control one video recorder, and
program the
AUX
button to control the other one.
TV
Note: The
button is not programmable.
Programming the remote control
Automatic code search
This method can be used to automatically find the most
appropriate code for your appliance.
1.
Switch on the appliance you wish to use the remote control
with.
2.
Press the relevant button for this appliance on the remote
control, and while holding this button down, press the
standby button until the light (
the remote control come on. Release both buttons.
3.
Point the remote control at the appliance and press
Wait until the light stops flashing. If the appliance has not gone
into standby mode after five seconds, press the
again to continue the search for the next set of codes. Repeat
this operation until the appliance goes into standby mode.
There are around 20 sets of codes.
4.
When the appliance goes into standby mode, switch it on again
without using the remote control. Press the
many times as is required to return the appliance to standby
mode.
5.
STOP
Press the
button and hold it down until the light (
the appliance buttons) of the remote control go off.
Note:You can cancel the programming operation at any time by
EXIT
pressing the
button.
4
,
DVD
,
SAT
,
AMP
and
or the appliance buttons) of
PLAY
.
PLAY
button
REV
button as
or
Advertisement
Table of Contents
