Table of Contents
Advertisement
Quick Links
QM26 and QMH26 Series Sensors
Instruction Manual
Stainless Steel and Hygienic Stainless Steel Sensors for Washdown and Chemical Compatibility
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety
applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output
condition.
QM26 Models
Stainless Steel Sensors for Washdown and Chemical Compatibility
Model
Mode
QM26E-5M
Emitter
QM26EQ5
QM26VNR-5M
QM26VNRQ5
Receiver
QM26VPR-5M
QM26VPRQ5
QM26VNLP-5M
QM26VNLPQ5
Polarized
Retroreflective
QM26VPLP-5M
QM26VPLPQ5
QM26ENXLPC-5M
Expert
QM26ENXLPCQ5
Polarized
QM26EPXLPC-5M
Retroreflective
QM26EPXLPCQ5
Original Document
166534 Rev. E
•
QM26: Washdown rated with convenient 25.4 mm (1 in) mounting spacing and 3 mm (0.125 in)
mounting hardware
•
QMH26: Hygienic shape for superior cleaning performance
•
Made from FDA compliant materials for worry-free use in food and pharmaceutical applications
•
Chemically resistant, non-toxic 316L stainless steel housing
•
Acrylic optical window with coating for resistance to hydrogen peroxide and alcohol
•
IP69K rated for use in harsh 1500 psi washdown environments at 80° C (176° F)
•
Withstands environmental temperature cycling from –30° to +60° C (–22° to +140° F)
•
Sealed housing and smooth joints minimize cleaning time and reduce bacterial accumulation
•
Sensor marking is chemically etched into the housing for long-lasting identification and to
eliminate food contamination
•
Push buttons and light pipes are over-molded to reduce crevices and provide excellent cleaning
and sealing results
•
High performance coaxial polarized retroreflective models for clear or transparent bottle and film
detection
•
Excellent background suppression performance with advanced ambient light suppression
•
Bright, visible red light spot on adjustable background suppression models makes alignment easy
•
Models have a hygienic design for easy cleaning and sanitizing
Range
8.5 m (27.8 ft)
3 m (9.8 ft) with
BRT-60X40C
™
Coaxial
2.6 m (8.5 ft) with
BRT-60X40C
Output
Connector
5 m (16.25 ft) cable, 4 wire
NA
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ft) cable, 4 wire
Complementary
NPN
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ft) cable, 4 wire
Complementary
PNP
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ft) cable, 4 wire
Complementary
NPN
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ft) cable, 4 wire
Complementary
PNP
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ft) cable, 4 wire
NPN
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ft) cable, 4 wire
PNP
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
16 October 2017
166534
Advertisement
Table of Contents
Related Manuals for Banner QM26 Series
Summary of Contents for Banner QM26 Series
- Page 1 QM26 and QMH26 Series Sensors Instruction Manual Stainless Steel and Hygienic Stainless Steel Sensors for Washdown and Chemical Compatibility • QM26: Washdown rated with convenient 25.4 mm (1 in) mounting spacing and 3 mm (0.125 in) mounting hardware • QMH26: Hygienic shape for superior cleaning performance •...
- Page 2 QM26 and QMH26 Series Sensors Model Mode Range Output Connector QM26VNAF400-5M 5 m (16.25 ft) cable, 4 wire Complementary Adjustable Field QM26VNAF400Q5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin 5 to 400 mm (0.2 in Background to 15.7 in) QM26VPAF400-5M 5 m (16.25 ft) cable, 4 wire...
-
Page 3: Sensor Installation
QM26 and QMH26 Series Sensors Sensor Installation Install the sensor so that the object to be detected moves horizontally to the sensor. Wiring Diagrams Wiring Key 1 = Brown 10-30V dc 10-30V dc 2 = White – – 3 = Blue Load Load 4 = Black... - Page 4 The remote input wire (pin 2/white wire) is used to to lock the push button, select Light or Dark Operate, or perform the desired Light ™ SET or Dark SET for the object. In contrast to other Banner Engineering sensors, the QM26 and QMH26 Expert coaxial polarized retroreflective sensors (XLPC models) use the duration between pull-high pulses on the remote input wire to both initiate the Light SET or Dark SET and to select the desired sensitivity simultaneously.
- Page 5 QM26 and QMH26 Series Sensors Push Button Remote Input Wire Result Not available Connect the remote input wire to +V dc for 4 ms or longer. The push button is disabled (locked). Not available Disconnect the remote input wire from +V dc. The push button is enabled (unlocked).
- Page 6 QM26 and QMH26 Series Sensors Push Button Remote Input Wire Result Clear the light path to the reflector. Clear the light path to the reflector. Press the button for 2 to 7 seconds until Push button only: The green and yellow LEDs Pulse the remote input wire to +V dc, then pull the the LEDs flash simultaneously, then flash simultaneously.
- Page 7 QM26 and QMH26 Series Sensors Dark SET for Maximum Operating Range Use either the button or the remote input wire procedure to configure the sensor. Push Button Remote Input Wire Result Block the light path to the reflector. Block the light path to the reflector. Press the button for 2 to 7 seconds until Push button only: The green and yellow LEDs Pulse the remote input wire to +V dc, then pull the...
-
Page 8: Specifications
4-wire 5 m (16.25 ft) cable or 4-pin M12 Euro-style quick disconnect connector with 200 mm (7.5 in) PVC pigtail, depending on model 100 mA per output Banner recommends using the 4-Pin Threaded M12/Euro-Style Cordsets— Off-state leakage current for load = 1500 Ω: Washdown, Stainless Steel cordsets listed in the Accessories section. - Page 9 QM26 and QMH26 Series Sensors QM26 Dimensions All measurements are listed in millimeters [inches], unless noted otherwise. QMH26 Dimensions All measurements are listed in millimeters [inches], unless noted otherwise. P/N 166534 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164...
-
Page 10: Performance Curves
QM26 and QMH26 Series Sensors Performance Curves Minimum Separation Distance AF200 Models AF400 Models Black / White Black / White Gray / White Gray / White White / White White / White Object / Background Object / Background 90% White Card Cutoff Setting (mm) 90% White Card Cutoff Setting (mm) Figure 5. - Page 11 QM26 and QMH26 Series Sensors Excess Gain 1000 1000 10000 DISTANCE (mm) Figure 7. Opposed Mode Models BRT-60x40C BRT-92x92C BRT-40x19A BRT-60x40IP69K BRT-THG-2-100 (2” x 2”) BRT-60x40C-PS BRT-40x19A-PS 1000 10000 DISTANCE (mm) ™ Figure 8. Expert Retroreflective Models (XLPC Models) BRT-60x40C BRT-92x92C BRT-40x19A BRT-60x40IP69K...
-
Page 12: Beam Patterns
QM26 and QMH26 Series Sensors AF200 Models AF400 Models 1000 1000 Setpoint: 15 mm Setpoint: 15 mm Setpoint: 200 mm Setpoint: 100 mm Setpoint: 400 mm Setpoint: 200 mm 1000 1000 1000 DISTANCE (mm) DISTANCE (mm) Figure 10. Adjustable Field Models (AFxxx Models) Beam Patterns -100 -150... - Page 13 QM26 and QMH26 Series Sensors AF200 Models AF400 Models DISTANCE (mm) DISTANCE (mm) Figure 14. Adjustable Field Models (AFxxx Models) Spot Size Versus Distance Clear Object Expert Retroreflective (XLPC) Models 100 x 100 80 x 80 60 x 60 40 x 40 20 x 20 0 x 0 DISTANCE (mm)
- Page 14 QM26 and QMH26 Series Sensors 4-Pin Threaded M12/Euro-Style Cordsets Cable: PVC jacket, PUR (polyurethane) connector body, nickel-plated brass coupling nut Conductors: 22 AWG, gold-plated contacts Conductors: 22 AWG, gold-plated contacts Voltage/Current Rating: 250 V ac/dc, 4.0 A Temperature: –40 °C to +105 °C (–40 °F to +221 °F) Environmental Rating: IP67/IP69K 4-Pin Threaded M12/Euro-Style Cordsets Model...
- Page 15 QM26 and QMH26 Series Sensors SMBQMH26-SS-150 ø 12 • Smooth surfaces for easy cleaning • Setscrew adjustment of ø 22 sensor • 316L stainless steel Retroreflectors All measurements are listed in millimeters, unless noted otherwise. BRT-60X40C BRT-92X92C • Rectangular, acrylic target •...
- Page 16 MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.