Download Print this page
Federal Signal Corporation COMMANDER Series Instruction Sheet

Federal Signal Corporation COMMANDER Series Instruction Sheet

Rotating lights

Advertisement

Quick Links

MODEL 371/371L
INSTRUCTION SHEET FOR COMMANDER®
MODEL 371/371L ROTATING LIGHTS
Address all communications and shipments to:
FEDERAL SIGNAL CORPORATION
Electrical Products Division
Service Department
2645 Federal Signal Drive
University Park, IL 60466-3195

Advertisement

loading
Need help?

Need help?

Do you have a question about the COMMANDER Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Federal Signal Corporation COMMANDER Series

  • Page 1 MODEL 371/371L INSTRUCTION SHEET FOR COMMANDER® MODEL 371/371L ROTATING LIGHTS Address all communications and shipments to: FEDERAL SIGNAL CORPORATION Electrical Products Division Service Department 2645 Federal Signal Drive University Park, IL 60466-3195...
  • Page 2: Installation

    INSTRUCTION SHEET FOR COMMANDER® MODEL 371/371L ROTATING LIGHTS SAFETY MESSAGE TO INSTALLERS, USERS AND MAINTENANCE PERSONNEL It is important to follow all instructions shipped with this product. This device is to be installed by a trained electrician who is thoroughly familiar with the National Electric Code/ Canadian Electric Code and will follow the NEC/CEC Guidelines as well as local codes.
  • Page 3 2. Surface Mounting (See figure 1) a. Using the gasket as a template, scribe four drill position marks on the mounting surface. Drill a 9/32" (7.1mm) diameter hole at each of the outside drill posi- tion marks for mounting. Drill or punch a 1-3/8" (34.9 mm) diameter hole at the center drill position mark for conduit entry.
  • Page 4 1. Disassemble the light as follows: a. Remove dome assembly by grasping the die-cast ring attached to the dome and turning it counter-clockwise. b. Remove three no. 10 hex head screws that secure motor mounting base to housing. c. Remove motor mounting base. d.
  • Page 5 A. Lamp Replacement (See figure 4) WARNING To avoid electrical shock hazards, do not replace lamp when power is applied. 1. Remove the dome assembly by grasping the die-cast ring attached to the dome and turning it counter-clockwise. If difficulty occurs removing the dome assem- bly, place a screwdriver blade against one of the four bosses on the die-cast ring attached to the dome.
  • Page 6 Distributor or Manufacturer’s Representative. At this time a brief explanation of the service requested, or the nature of the malfunc- tion, should be provided. Address all communications and shipments to: FEDERAL SIGNAL CORPORATION Electrical Products Division Service Department 2645 Federal Signal Drive...
  • Page 7: Pipe Mount

    PIPE MOUNT SURFACE MOUNT 371 LIGHT ASSEMBLY GASKET DRILL (3) 9/32" (7.143 mm) HOLES 1" NPT PIPE MOUNTING SURFACE 1/4" WASHERS 1/4" SCREWS 290A3939...
  • Page 8 TURN DIE CAST RING DOME ASSEMBLY COUNTER-CLOCKWISE TO REMOVE DIE CAST RING LOCKING SCREW ADJUST LAMP TO PIVOT SCREWS (2) DESIRED POSITION 290A3940...
  • Page 9 DOME TURN DIE CAST RING ASSEMBLY COUNTER-CLOCKWISE TO REMOVE DIE CAST RING SCREWS, #10 HEX HEAD (3) TERMINAL MOTOR BLOCK MOUNTING BASE GASKET GROUND SCREW BASE 290A3941...
  • Page 10 DOME ASSEMBLY TURN DIE CAST RING COUNTER-CLOCKWISE TO REMOVE DIE CAST RING CONNECTOR LAMP LAMP TERMINALS LAMP RETAINER LIFT UP SPRING CLIP AND ROTATE LAMP RETAINER FORWARD 290A3942...
  • Page 11 MODEL 371 INSTALLATION AND SERVICE INSTRUCTIONS FOR SHOCK MOUNT KIT FOR COMMANDER ® MODEL 371 LIGHTS Address all communications and shipments to: FEDERAL SIGNAL CORPORATION Electrical Products Division 2645 Federal Signal Drive University Park, IL 60466-3195...
  • Page 12 INSTALLATION AND SERVICE INSTRUCTIONS FOR SHOCK ® MOUNT KIT FOR COMMANDER MODEL 371 LIGHTS SAFETY MESSAGE TO INSTALLERS, USERS AND MAINTENANCE PERSONNEL It is important to follow all instructions shipped with this product. This device is to be installed by a trained electrician who is thoroughly familiar with the National Electric Code/Canadian Electric Code and will follow the NEC/CEC Guidelines as well as local codes.
  • Page 13 Distributor or Manufacturer’s Representative. At this time a brief explanation of the service requested, or the nature of the malfunction, should be provided. Address all communications and shipments to: FEDERAL SIGNAL CORPORATION Electrical Products Division Service Department 2645 Federal Signal Drive...
  • Page 14 VIBRATION MOUNT GROMMET LOCKWASHER 1/4-20 HEX NUT 290A3806 A = 6.25” 158.8 mm B = 9/32” 7.1 mm C = 3/8” 9.5 mm D = 120º 290A3807 2561547A FEDERAL SIGNAL CORPORATION Rev. A 10/99 Electrical Products Division Made in U.S.A.
  • Page 15 2561668A REV. A 9/00 Printed in U.S.A. INSTALLATION AND SERVICE INSTRUCTIONS FOR MOTOR REPLACEMENT KIT FOR COMMANDER ® MODEL 371/371L LIGHTS SAFETY MESSAGE TO INSTALLERS, equipment has been damaged, do not attempt to install or operate it. File a claim immediately with USERS AND MAINTENANCE PERSONNEL the carrier stating the extent of the damage.
  • Page 16 Before installing the new motor, crimp the provided ring terminals on the new motor Address all communications and shipments to: leads. FEDERAL SIGNAL CORPORATION g. Assemble the new motor plate assem- Electrical Products Division bly to the mounting base making sure that the worm...
  • Page 17 MODEL 371BRCKT INSTRUCTION SHEET FOR MOUNTINg BRaCKET KIT MODEL 371BRCKT ® FOR COMMaNDER LIgHTS Address all communications and shipments to: FEDERaL SIgNaL CORPORaTION Electrical Products Division 2645 Federal Signal Drive University Park, IL 60466-3195...
  • Page 18 INSTALLATION AND SERVICE INSTRUCTIONS FOR MOUNTING BRACKET MODEL 371BRCKT FOR COMMANDER LIGHTS ® SaFETY MESSagE TO INSTaLLERS, USERS aND MaINTENaNCE PERSONNEL It is important to follow all instructions shipped with this product. This device is to be installed by a trained electrician who is thoroughly familiar with the National Electric Code/Canadian Electric Code and will follow the NEC/CEC Guidelines as well as local codes.
  • Page 19 Manufacturer’s Representative. At this time a brief explanation of the service requested, or the nature of the malfunction, should be provided. Address all communications and shipments to: FEDERaL SIgNaL CORPORaTION Electrical Products Division Service Department 2645 Federal Signal Drive University Park, IL 60466-3195...
  • Page 20 MODEL 371 LIGHT CONDUIT PLUG MOUNTING SCREWS (USER SUPPLIED) BRACKET BRACKET MOUNTING SCREWS MOUNTING SURFACE 290A3805 2561546A Rev. A 10/99 Made in U.S.A.

This manual is also suitable for:

Commander 371Commander 371l