Download
Share
Print this page
Precor Experience Series Assembly Manual
  1. Manuals
  2. Brands
  3. Precor Manuals
  4. Fitness Equipment
  5. Experience Series
  6. Assembly manual
Precor Experience Series Assembly Manual

Precor Experience Series Assembly Manual

Hide thumbs Also See for Experience Series:

Advertisement

Quick Links

Download this manual See also: Service Manual
This addendum accompanies your equipment documentation and is additional
information concerning the heart rate features for your equipment and console.
Important
The heart rate features are intended for reference only. They may not be accurate
for every user or at every speed and are not intended for use as a medical device.
Holding the heart rate handle touch sensor while exercising at higher intensity
may also decrease accuracy of the heart rate reading and is not recommended.
Please also read your product documentation and visit:
www.precor.com/en-us/customer-service/faq.
P/N 305324-101 rev A, ENU
©Precor Incorporated | October 2017

Advertisement

loading

Related Manuals for Precor Experience Series

Summary of Contents for Precor Experience Series

  • Page 1 Holding the heart rate handle touch sensor while exercising at higher intensity may also decrease accuracy of the heart rate reading and is not recommended. Please also read your product documentation and visit: www.precor.com/en-us/customer-service/faq. P/N 305324-101 rev A, ENU ©Precor Incorporated | October 2017...
  • Page 2 A variety of manual and preset programs such as Lose Weight, Be Fit, Get Toned, and Push Performance can help trainers and users meet their goals and build training programs tailored to produce the best possible results. Instructional videos and complete EFX operating instructions are available at www.precor.com. Also available at precor.com...
  • Page 3 You can vary your stride style by lengthening your stride to a maximum of 36 inches. Step 7: Press Pause to finish. To dismount safely, hold the fixed hand Check out our trend-based workouts and Precor product tutorials at rails then slowly step off the AMT. www.precor.com/education.
  • Page 4 WARNING Before you connect any cables to the console, make sure that the equipment is not connected to any external power source or plugged into the wall. For more equipment information and troubleshooting, visit us at www.precor.com. Connector Cable Connector Type...
  • Page 5 Verify IP connectivity. Go to System Settings > Connectivity. The IP address field should be populated (10.15.80.90, for example). Then, to register the equipment, make sure you have this info: Location code  Precor technician account name and password  Serial number from the base ...
  • Page 6 4. Touch OK. The System Settings banner hours, maximum treadmill speed, or maximum pause time. appears. For complete console operating instructions and troubleshooting, visit us at www.precor.com. P62 Console Getting Started Guide | P/N 304240-101 rev A, ENU ©2016 Precor Incorporated | August 2016...
  • Page 7 Start exercising Ready to up your game and give your clients great workouts and training programs? Take advantage of Precor’s product tutorials, best-in-class training resources, and content libraries — which we refresh regularly (select regions only) — on www.precor.com. CAUTION Before beginning any fitness program, see your physician for a thorough medical exam.

  • Page 8: Assembly Guide

    Experience™ Series Adaptive Motion Trainer® (AMT®) Assembly Guide English Français Deutsch 日本語 中文 Español Português Equati on 1: E nglis h...
  • Page 10 Start assembling the AMT while it is still on the pallet. Remove the AMT from the pallet when instructed to so in this guide. Follow the steps in the order listed in this assembly guide. For more product information, visit us at www.precor.com. WARNING At least two people are required to assemble the equipment. DO NOT attempt assembly by yourself.
  • Page 11 Required tools Hardware kit #2 Phillips screwdriver • Component Quantity Component Quantity Rubber mallet • 7/16-inch open-end wrench • Nylon lock nuts (5/16- Screw SAE standard socket set • inch) (#10 x 1 1/4-inch) Wire cutter • Two #1 Phillips screwdrivers •...
  • Page 12 Begin assembly Important The side arm supports are shipped with foam blocks inserted in one end. Attach the bolt using the nut (see Figure 3). Partially tighten. These blocks prevent fasteners from falling into the supports. DO NOT remove the foam Important Insert the bolt into the inside of the side arm and attach the nut to blocks or push them down into the supports.
  • Page 13 Remove and throw away the two #10 x 3/4-inch Phillips head screws To attach the lower side arm supports: securing the upper back corner of the inner plastic molding to the end of Place the two side arm supports against the center support and insert a the right side arm.
  • Page 14 Remove the AMT from the pallet After the side arm supports are secured, move the AMT off of its shipping pallet to the location where it will be used. CAUTION DO NOT move the AMT off its shipping pallet without assistance. DO NOT apply any weight to the side arms of the AMT until the side arm supports have been installed.
  • Page 15 Remove the access covers Extend a finger through the gasket opening and under the front edge of the top Removing the front and side access covers provides sufficient space to install the cover. While pressing upward on the top cover, use the heel of your hand to tap console cables.
  • Page 16 Rewire the AMT for a touchscreen console DANGER DO NOT attempt to connect electrical power until all assembly Thread the cables for each part as follows: procedures are complete and the console is properly installed. TV connection a. Install the TV (coax) coupler, star washer, and nut, into the jack plate at the Retrieve the following parts from the console package: lower end of the AMT and tighten (see Figure 12).
  • Page 17 Remove the tie from the base data cable. Group that cable with the others and To continue the wiring: thread them upward through the center support and out through the center Pass the ends of all cables through the opening in the top of the cable channel opening in the console mount, making sure that the heart rate sensor cable and secure them in the cable clips.
  • Page 18 Route cables under the rear pedestal (optional) When the AMT faces away from the cable raceway, use the conduit included in the To replace the access covers: hardware kit to route the Ethernet, TV, and power cables underneath the center of 4.
  • Page 19 Position the handlebars Reinsert the two set screws. Leave the screws partially tightened until you have During shipment, the AMT is packed with its handlebars reversed. Two set screws adjusted both handlebars. are threaded into each handlebar. The plastic boots that eventually cover the screws are positioned just above them on the handlebars.
  • Page 20 Level the AMT It is important to level the AMT properly every time you move it. Important To allow the rear pedestal to fit properly, the adjustable feet must extend at least 2 inches (5 cm) below the side arm supports. Extend the feet before you remove the CAUTION To eliminate movement, make sure the adjustable feet are in spacer block (as described in To add the side arm supports), to ensure that they are...
  • Page 23 AMT Assembly Guide | P/N 304438-101 rev B, ENU ©2016 Precor Incorporated | October 2016...
  • Page 26          ...
  • Page 27                          ...
  • Page 30   ...
  • Page 33 NOTES...
  • Page 35 NOTES Cardio Safety Regulatory Warranty | P/N 305035-101, rev B, ENU...
  • Page 36 Cardio Equipment Quick Reference Maintenance Guide...
  • Page 37 Cardio Equipment Quick Reference Maintenance Guide For complete maintenance and cleaning information, visit us at www.precor.com. For torque settings, review the product Assembly Guide included with your equipment, or go to www.precor.com for more information. Important The owner is responsible for maintaining Precor equipment in their facility based on the recommendations below and any accompanying material.

  • Page 38: Monthly Maintenance Tasks

    Clean the drive belts and pulleys with a small wire brush. • Vacuum out any debris, being careful not to bring the vacuum cleaner nozzle too close to any circuit board. Precor recommends you use a vacuum • that protects against static buildup.

  • Page 39: Quarterly Maintenance Tasks

    Check tension of the running belts and adjust if necessary. Inspect belts for excessive wear.  Perform software diagnostics and check LED function.  AMT only Inspect the gas spring shock. Contact Precor Customer Support if you have questions.  EFX only Check the belt tension. ...

  • Page 40: Error Codes

    Displays the message, "Belts change required", in place of the standard banner AMT only text. No workout can be started. Contact a Precor-certified service technician. 17-20, 25, 85-88 Turn the equipment off and on. Repeat twice. If the message still appears, contact treadmill only a Precor certified service technician.

  • Page 41: Moving The Equipment

    Important The plastic end caps on Precor treadmills are designed specifically for lifting. Working with your assistant, place a hand under each side of the end cap. Then, using proper lifting techniques, lift the rear of the treadmill so that it rolls on its front...
  • Page 42 Proper alignment allows the belt to remain centered and ensures smooth operation. Realigning the belt takes a few simple adjustments. If you are unsure about this procedure, contact Precor Customer Support. CAUTION DO NOT adjust the running belt when someone is standing on it.
  • Page 43 Adjust the running belt (treadmill only) If you are unsure about adjusting the running belt, contact Precor Customer Support. CAUTION Take special care when aligning the running belt. The treadmill will not stop immediately if an object becomes caught in the belt or rollers. Turn OFF the treadmill while adjusting or working near the rear roller.
  • Page 44 The treadmill must remain out of service until the stop switch is repaired. Place an "out of order" sign on the treadmill and contact Precor Customer Support. 6. Turn the treadmill power switch to Off. The On/Off switch is located at the front of the treadmill.
  • Page 45 8. Press Quick Start. Important You have three seconds before the treadmill belt begins to move. Hold the handlebars or side hand rails to help maintain balance. 9. The treadmill will run at 1 mph. Allow the treadmill to run for one minute while keeping the towel firmly in place. CAUTION Press the safety stop key if the towel becomes loose to prevent it from being pulled into the treadmill’s rollers.

This manual is also suitable for:

Amt 883Amt 885