Related Manuals for Noaw A300
Summary of Contents for Noaw A300
- Page 1 Automatic slicing machines Models A300 – A330 – A350 A300/CL – A330/CL – A350/CL A300I/CL – A330I/CL – A350I/CL Instructions for use and maintenance Edition February 2018...
-
Page 2: Table Of Contents
Use and maintenance LIST OF CONTENTS Page 1. INTRODUCTION ......................2 1.1 Purpose of the manual ......................2 1.2 Use of the machine .........................2 2. GENERAL INFORMATION ..................... 2 2.1 Machine limits, safety regulations ..................2 2.2 Guarantee and manufacturer’s responsibility ...............3 2.3 The user’s obligations ......................3 2.4 Markings - Plates ........................4 3. -
Page 3: Introduction
Use and maintenance 1. INTRODUCTION 1.1 Purpose of the manual This publication contains all the information necessary for the use and maintenance of the automatic slicing machines to be used for food, with circular blade, models Ø300, Ø330 and Ø350mm. The purpose of this manual is to allow the user, above all the direct user, to take every precaution and arrange all human and material means necessary for a safe and lengthy use of these machines. -
Page 4: Guarantee And Manufacturer's Responsibility
Use and maintenance • Do not remove the transparent protection and do not change or exclude the mechanical and electrical protections; • Only slice permitted products; do not try slicing any products that are not allowed; • The area around the machine, where the food is laid and the floor where the operator works must always be kept clean and dry;... -
Page 5: Markings - Plates
Use and maintenance 2.4 Markings - Plates The following plate is installed on the machine: manufacturer’s identification plate, machine plate, technical data plate and EC marking. In requests for technical assistance or ordering spare parts, always refer to the data plate and the serial number of the machine. 3. -
Page 6: Technical Data Sheet
Use and maintenance 3.3 Technical data sheet DIMENSIONS Mod. A300 A330 A350 TECHNICAL DATA Mod. A300 A330 A350 Blade Blade turns/1’ giri/min Carriage movement Cut’s capacity Ø 220x185 220x195 220x205 Cut’s capacity □ Thickness adjuster Net weight Motor single phase 0.39... - Page 7 Use and maintenance DIMENSIONS Mod. A300/CL A330/CL A350/CL 1020 1020 1020 TECHNICAL DATA Mod. A300/CL A330/CL A350/CL Blade Blade turns/1’ giri/min Carriage movement Cut’s capacity Ø 305X220 305X230 305X240 Cut’s capacity □ Thickness adjuster Net weight Motor single phase 0.39 0.39...
- Page 8 Use and maintenance DIMENSIONS Mod. A300I/CL A330I/CL A350I/CL 1020 1020 1020 TECHNICAL DATA Mod. A300I/CL A330I/CL A350I/CL Blade Blade turns/1’ giri/min Carriage movement Cut’s capacity Ø 305X220 305X230 305X240 Cut’s capacity □ Thickness adjuster Net weight Motor single phase 0.45 0.45 0.45 Motor three phase...
-
Page 9: Description
Use and maintenance 4. DESCRIPTION 4.1 Main components Feed cable Identification plate, technical data and EC marking Push button control panel Graduated knob for slice thickness Meat table Safety guard Product fences Blade Sharpener knob Slice deflector Foot Knob for plate pushing Meat table support Plate blocking handle Base... -
Page 10: General Description
Use and maintenance 4.2 General description The machine offers the user: maximum safety when in use, during cleaning and ordinary maintenance; maximum hygiene from the use of stainless materials or adequately protected against oxidization together with an attentive design of all the parts that come into contact with food;... -
Page 11: Installation
Use and maintenance 5. INSTALLATION 5.1. Installing the machine The slicing machine must be placed on a horizontal flat surface which is stable and non-slip, suitable for sustaining the weight of the machine and the food; a support column with top is available on request. -
Page 12: Push Button Control Panel
Use and maintenance 5.4. Push button control panel 1. Off button 2. Light of off button 3. On button 4. Light of on button 5. Speed button 6. Light of speed button (from 1 to 3 led) One led on: low speed Two led on: intermediate speed Three led on: high speed 7. -
Page 13: Cleaning The Slicer
Use and maintenance Note: when you push the OFF button, you stop the blade and the carriage movement. But the slicer keeps the settings regarding speed and stroke, so when you push the ON button the slicer restarts with the same carriage run and speed before the stopping. If you want to stop the carriage movement, you can turn the function mode selector knob counterclockwise. -
Page 14: Maintenance And Repairs
Use and maintenance 7. MAINTENANCE AND REPAIRS 7.1 General information The operator is allowed to carry out the following maintenance: Blade sharpening, periodically; The interval and length of the sharpening obviously depend on the use of the machine (work times and type of product used) Lubrication of the carriage guide bars, weekly;... -
Page 15: Lubricating The Guide Bars Of The Carriage (Weekly)
Use and maintenance 7.2.3 Carrying out the sharpening 6. Release it and completely retighten the blocking knob; NOTE: Before starting this operation, check 7. Start the machine by pressing the ON that the grindstones have been cleaned. button; 1. Check that the slicer is properly connected to the electrical line and that the slice thickness WARNING: This... -
Page 16: Lubricating The Transversal Guide Rods Of The Plate And Food Press (Weekly)
Use and maintenance WARNING: Only use white Vaseline oil. DO NOT USE VEGETABLE OILS! 1. Move the carriage as close as possible to the operator; 2. Insert the oiler in the special hole; 3. Squeeze the oiler so that a small amount of oil goes into the hole;... - Page 17 Use and maintenance...
- Page 18 Use and maintenance...
-
Page 19: Dismantling The Slicing Machine
Use and maintenance 9. DISMANTLING THE SLICING MACHINE The machines are made up of: aluminum/magnesium alloy structure; insertions and various in stainless steel; electric parts and wires; electric motor; plastic materials, etc. If disassembly and dismantling are to be carried out by a third party, only consult firms that are authorized in the demolition of the above mentioned materials.
Need help?
Do you have a question about the A300 and is the answer not in the manual?
Questions and answers