Related Manuals for LaserLiner EvolutionCross-Laser 8P PowerBright
Summary of Contents for LaserLiner EvolutionCross-Laser 8P PowerBright
- Page 1 EvolutionCross-Laser 8P PowerBright 4H 4V 1D 3-10 Bedienungsanleitung 11-18 Operating instructions 19-26 Gebruiksaanwijzing 27-34 Mode d´emploi...
- Page 2 EvolutionCross-Laser 8P PowerBright Optional: max. 50 m range...
-
Page 3: General Safety Instructions
Any tampering by unauthorised persons will render this warranty void. In the event that you need to claim warranty, please take the complete device together with all information and the invoice to one of our dealers or send it in to Umarex-Laserliner. ENGLISH... - Page 4 EvolutionCross-Laser 8P PowerBright Laser emitting window Battery compartment Continuous horizontal 360° laser line Knob for precision adjustment 5/8” thread (underside) Window for plumb laser (underside) Adjustable feet with removable rubber caps Tripod adapter Vertical laser line/ slope function: set the slope...
- Page 5 EvolutionCross-Laser 8P PowerBright Battery (NiMH) charging • Charge the batteries (NiMH) fully before using the laser unit. Insert only rechargeable (i.e. secondary) batteries into the charging unit. Be sure that the batteries are marked with the label „RECHARGEABLE“. • Insert the rechargeable batteries into the charger and connect the charger to the mains power supply.
- Page 6 EvolutionCross-Laser 8P PowerBright Manual Slope function This function deactivates the automatic sensor, which enables slopes to be set. Press the H slope button and hold it down for 3 seconds until the auto LED starts to flash very rapidly. The V1, V2 buttons are used to re-adjust the slope by means of a motor.
- Page 7 EvolutionCross-Laser 8P PowerBright Manual re-adjustment: Steeper slopes can be set using the angle plate, which is available as an optional extra (product ref. 080.75). To this end you need to use a crank tripod, such as the 300 cm professional crank tripod, product ref. 080.34.
- Page 8 EvolutionCross-Laser 8P PowerBright Preparing the calibration check: It is possible for you to check the calibration of the laser. To do this, position the device midway between 2 walls, which must be at least 5 metres apart. Switch the device on (Laser cross ON). The best calibration results are achie- ved if the device is mounted on a tripod.
- Page 9 EvolutionCross-Laser 8P PowerBright Power indicator Switch accuracy short range / long range Sensitivity indicator light RX 51: Close range max. 15 m green – Long range max. 50 m red ON / OFF switch Sound ON / OFF Receiver field for laser beam LED’s for Laserindication...
- Page 10 Operating temperature 0°C ... + 50°C Storage temperature -10°C ... + 70°C Article-No. (ECL) 048.200A EvolutionCross-Laser 8P PowerBright RX Subject to technical alterations 06/2009 Note: Regularly check the calibration before use, after transport and after extended periods of storage ENGLISH...
- Page 11 Zubehör (optional) Accessories (optional) Accessoires (optioneel) Accessoires (en option) Art.-Nr: 023.61A Art.-Nr: 090.120A Art.-Nr: 033.20-1 Art.-Nr: 080.30 ECL 8P PowerBright: optional ECL 8P PowerBright RX: inclusive...
- Page 12 EvolutionCross-Laser 8P PowerBright Laserstrahlung! Nicht in den Strahl blicken oder direkt mit optischen Instrumenten betrachten. Laser Klasse 2 M EN60825-1:2007-10 Laser radiation! Do not look into the beam or observe it directly with optical instruments. Laser class 2 M EN60825-1:2007-10...