Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hilti DSF 1030-TS
Summary of Contents for Hilti DSF 1030-TS
- Page 1 DSF 1030TS English Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
- Page 2 Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
- Page 3 DSF 1030TS Original operating instructions Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
- Page 4 Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
-
Page 5: Table Of Contents
Contents Information about the documentation ......2 1.1 About this documentation ........2 1.2 Explanation of signs used . -
Page 6: Information About The Documentation
Transport and storage ........15 8.1 Transporting the floor saw trolley . -
Page 7: Product Information
Wear protective gloves Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed. - Page 8 ▶ Wear protective gloves also when changing the tool. Touching the accessory tool can result in cuts and burns. ▶ Ensure that adequately-sized supports are correctly installed so that the remaining structure retains its stability even after completion of the cutting work and removal of the part cut away.
-
Page 9: Description
Description Overview of the product 2153083 English *2153083* Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00... -
Page 10: Intended Use
Before use, the operator must have received the appropriate training by a Hilti specialist on safe use of the product. -
Page 11: Traction Drive
You can find other system products approved for use with this product at your local Hilti Center or online at: www.hilti.com Traction drive 3.5.1 Drive principle The mount for the saw head on the floor saw trolley incorporates gear wheels that mesh with the saw head advance motion drive. -
Page 12: Technical Data For The Floor Saw
Technical data for the floor saw Further data not listed here corresponds to the data for the electric wall saw used and can be found in the operating instructions for the applicable wall saw. Suitable saws • DST 10CA electric wall •... - Page 13 1. If necessary, loosen the securing bolts until the toothed discs no longer mesh and are thus free to rotate relative to each other. 2. Fold out the handlebar and adjust it to suit your body height so that you can steer the trolley easily with your hands on the grips.
-
Page 14: Bringing The Pointer Of The Cutting Line Indicator Into The Working Position
Bringing the pointer of the cutting line indicator into the working position. 1. Pull the securing pin out of the hollow bolt. 2. Pull the pointer out until the hole in the hollow bolt (at the pointer side) is aligned with the hole in the pointer. -
Page 15: Removing The Electric Wall Saw From The Floor Saw Trolley
1. Release the saw head clamping levers and bring them into the “released” detent position (see section on mounting the saw head in the operating instructions for the electric wall saw). 2. Place the saw head on the saw head mount on the floor saw trolley so that the guide rollers are brought into the position shown in the illustration. -
Page 16: Mounting The Cutting Line Indicator On The Opposite Side
WARNING Risk of injury! Inadvertent starting of the saw is hazardous. ▶ Always press the EMERGENCY OFF button on the remote control unit before carrying out any work on the saw. 1. Close the water supply valve and disconnect the water hose from the hose connector on the water supply system. -
Page 17: Preparing The Floor Saw For Use
Preparing the floor saw for use 1. Bring the blade guard holder into the 12 o'clock position (see operating instructions for the electric wall saw). 2. Fit the saw blade (see operating instructions for the electric wall saw). Technical data Saw blade diameter (when using the 600 mm …... -
Page 18: Adjusting The Cutting Line Indicator
5. Select one of the following alternatives. ▶ If the following conditions are met, also take this action: Conditions: Cutting using manual saw advance ▶ Make sure that the traction drive is disengaged. ▶ With both hands on the two grips provided, push the floor saw trolley in the cutting direction. -
Page 19: Care And Maintenance
6. Insert the securing pin. 7. Retighten the locknut. Care and maintenance ▶ Keep the product, especially the grips, dry, clean and free from oil and grease. ▶ Do not allow the dirt and slurry adhering to parts to dry out. Accordingly, clean the entire set of equipment immediately after finishing work and before long breaks between periods of use. - Page 20 ▶ Increase or, respectively, or too high. reduce saw blade speed. Disposal Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. English 2153083 *2153083* Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
- Page 21 In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information. 2153083 English *2153083* Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
- Page 22 English 2153083 *2153083* Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
- Page 23 2153083 English *2153083* Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
- Page 24 *2153083* 2153083 Hilti = registered trademark of Hilti Corp., Schaan 20190507 Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00...
Need help?
Do you have a question about the DSF 1030-TS and is the answer not in the manual?
Questions and answers