Hilti DSH 700 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Saw
  5. DSH 900
  6. Operating instructions manual

Hilti DSH 700 Operating Instructions Manual

Dsh 700/ dsh 900 cut-off saw
Hide thumbs Also See for DSH 700:
Table of Contents

Advertisement

Quick Links

See also: Operating Instructions
Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01
DSH 700 /
DSH 900
Operating instructions
Mode d'emploi
Manual de instrucciones
en
fr
es

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DSH 700 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hilti DSH 700

Summary of Contents for Hilti DSH 700

  • Page 1 DSH 700 / DSH 900 Operating instructions Mode d’emploi Manual de instrucciones Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...

  • Page 2: Product View

    +] +[ This Product is Listed Ce produit est homologué Producto homologado por Este produto está registrado "≠ "± +≠ "[ +± +Ç +“ "“ "Ç 5 +} "# Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...
  • Page 3 2/7/9 Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...
  • Page 4 1/15 3/10 5/13 Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...
  • Page 5 9/10 Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...
  • Page 6 1/12 0.5mm Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...
  • Page 7 Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...

  • Page 8: Table Of Contents

    Keep these pages open while studying the oper- ating instructions. DSH-FSC saw carriage 2 In these operating instructions, the designation “the ma- chine” always refers to the DSH 700 or DSH 900 gasoline- Grip powered cut-off saw. Throttle trigger...

  • Page 9: Dsh-Fsc Saw Carriage

    Hilti representative fumes. discs used or service department. Obligation signs Type: Generation: 01...

  • Page 10: Description

    NOTE tion. Various grit types such as aluminum oxide, silicon car- To avoid the risk of injury, use only genuine Hilti acces- bide, zirconium, etc., with a different bonding material sories and cutting tools. (matrix) or matrix hardness, are available depending on Observe the safety rules and operating instructions for the construction material to be cut.

  • Page 11: Accessories

    3 Accessories Accessories for the DSH 700 and DSH 900 Designation Short designation Item number, description Diamond cutting disc 000000, See main catalog. Abrasive cutting disc 000000, See main catalog. Two-stroke oil DSH (1 L) 365826 Water supply unit DWP 10...

  • Page 12: Technical Data

    4 Technical data Right of technical changes reserved. DSH 700 30 cm DSH 700 35 cm DSH 900 35 cm DSH 900 40 cm Machine / 12" / 14" / 14" / 16" Motor type Two-stroke / single- Two-stroke / single-...

  • Page 13: Safety Instructions

    “live” wire will make exposed metal parts of the injury. machine “live” and shock the operator. c) Use only the genuine Hilti accessories or ancillary Children must be instructed not to play with the equipment listed in the operating instructions. Use machine.
  • Page 14 Fit the filled water tank to the saw carriage only explosion. Take care to ensure that the sparks after fitting the saw to the saw carriage. This will generated do not ignite flammable (gasoline, dry grass, etc.) or explosive (gas, etc.) substances. prevent the saw carriage falling over.

  • Page 15: Before Use

    Correctly sized flanges support the cutting disc and 5.9 Safety warnings for abrasive cutting-off thus reduce the possibility of disc breakage. operations k) When fitting the cutting disc, always take care to ensure that the disc’s specified direction of rotation corresponds to the direction of rotation of the machine.
  • Page 16 Use the following Check to ensure there is no leakage from the machine. mix ratio with Hilti two-stroke oil: 1 part oil + 50 parts Don’t start the machine if fuel is found to be leaking gasoline.
  • Page 17 CAUTION Hold the guard by the grip provided and rotate it to the desired position. Don’t use synthetic resin-bonded fiber-reinforced cutting discs that have exceeded their use-by date. 6.4 Converting the saw from normal cutting mode CAUTION to flush cutting mode 4 Don’t use damaged diamond cutting discs (cracks in the steel disc, broken or polished segments, damaged arbor hole, bent or distorted steel disc, heavy discol-...

  • Page 18: Operation

    12. Tighten the three clamping nuts securely (18 Nm). NOTE 13. Fit the rear drive belt cover and secure it with the Especially when using the machine in this configuration four screws. for the first time, check to ensure that the throttle cable is 14.
  • Page 19 WARNING DANGER After fitting a new cutting disc, the machine must be Guide the machine evenly and do not apply lateral allowed to run at full speed under no load for approx. pressure to the cutting disc. Always bring the machine 1 minute.

  • Page 20: Care And Maintenance

    8 Care and maintenance machine should stand upright and should not be laid on its side. Take care to ensure that no dust finds its way onto the underlying filter screen. NOTE Change the air filter if motor performance drops notice- WARNING ably or if the machine becomes difficult to start.

  • Page 21: Adjusting The Carburetor

    All other adjustments must Use the spark plug wrench to screw the spark plug be carried out at a Hilti service center. into the cylinder (12 Nm). Fit the ignition cable connector to the spark plug.

  • Page 22: Cleaning

    If necessary, the machine should be repaired Remove the spark plug. by Hilti Service. Pour a little two-stroke oil into the cylinder (1 to 2 teaspoons). 8.11 Checking the power tool after care and Pull the starter handle a few times.
  • Page 23 The disc specification is unsuitable Change the specification or request for the material to be cut. advice from Hilti. Drive belt or cutting disc slips. Check the drive belt tension and disc clamping parts and eliminate the fault.

  • Page 24: Disposal

    10 Disposal Most of the materials from which Hilti machines or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back old machines and appliances for recycling. Ask Hilti customer service or your Hilti representative for further information.

  • Page 25: Manufacturer's Warranty

    Any replace- charge to the owner if the part is still under warranty. Hilti ment part or service that is equivalent in performance is liable for damages to other engine components caused and durability may be used in non-warranty maintenance by the failure of a warranted part still under warranty.
  • Page 26 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3503 | 0712 | 00-Pos. 3 | 1 Printed in Italy © 2012 Right of technical and programme changes reserved S. E. & O 288292 / A3 Printed: 08.07.2013 | Doc-Nr: PUB / 5069771 / 000 / 01...

Table of Contents

Save PDF