Hilti DSH 700 Operating	 Instruction

Hilti DSH 700 Operating Instruction

Cut-off saw
Hide thumbs Also See for DSH 700:

Advertisement

Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00
DSH 700 /
DSH 900
Bedienungsanleitung
Mode d'emploi
Istruzioni d'uso
Manual de instrucciones
Manual de instruções
Gebruiksaanwijzing
Használati utasítás
Návod k obsluze
Návod na obsluhu
Upute za uporabu
Navodila za uporabo
Ръководство за обслужване
Instrucţiuni de utilizare
de
fr
it
es
pt
nl
hu
cs
sk
hr
sl
bg
ro

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DSH 700 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hilti DSH 700

  • Page 1 DSH 700 / DSH 900 Bedienungsanleitung Mode d’emploi Istruzioni d’uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Használati utasítás Návod k obsluze Návod na obsluhu Upute za uporabu Navodila za uporabo Ръководство за обслужване Instrucţiuni de utilizare Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...
  • Page 2 +] +[ "≠ "± +≠ "[ +± +Ç +“ "“ "Ç 5 +} "# Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...
  • Page 3 2/7/9 Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...
  • Page 4 1/15 3/10 5/13 Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...
  • Page 5 9/10 Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...
  • Page 6 1/12 0.5mm Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...
  • Page 7 Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...
  • Page 8: Table Of Contents

    Keep these pages open while studying the oper- ating instructions. DSH-FSC saw carriage 2 In these operating instructions, the designation “the ma- chine” always refers to the DSH 700 or DSH 900 hand- Grip held gas saw. Throttle trigger...
  • Page 9 The type designation and serial number can be found on Warning signs the type identification plate on the machine. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Type: General...
  • Page 10: Description

    Abrasive cutting discs for gasoline-powered cut-off saws tion. are used mainly for cutting ferrous and non-ferrous To avoid the risk of injury, use only genuine Hilti ac- metals. cessories and cutting tools. Observe the safety rules and operating instructions for NOTE the accessories used.
  • Page 11: Accessories

    3 Accessories Accessories for the DSH 700 and DSH 900 Designation Short designation Item number, description Diamond cutting disc 000000, See main catalog. Abrasive cutting disc 000000, See main catalog. Two-stroke oil DSH (1 L) 365827 Water supply unit DWP 10...
  • Page 12: Technical Data

    Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the machine and the accessories, keep the hands warm, organisation of work patterns. DSH 700 30 cm DSH 700 35 cm...
  • Page 13: Safety Instructions

    Do not overload the machine. It will work more tating drill bits, discs or blades, etc. may lead to efficiently and more safely within its intended per- injury. formance range. c) Use only the genuine Hilti accessories or ancillary equipment listed in the operating instructions. Use...
  • Page 14 g) Never use the power tool without the guard c) Don’t work in closed rooms. Carbon monoxide, (hood). unburned hydrocarbons and benzene in the exhaust h) Take steps to ensure that flying sparks from the gas may cause asphyxiation. power tool do not present a hazard, i.e. by striking d) Keep the workplace tidy.
  • Page 15 b) Allow the machine to cool before refueling. 5.8 Requirements to be met by users c) Use a suitable funnel when refueling. a) Improve the blood circulation in your fingers by d) Don’t use the gasoline or other flammable liquids relaxing your hands and exercising your fingers for cleaning.
  • Page 16: Before Use

    Use the following The two-stroke motor runs on a mixture of gasoline and mix ratio with Hilti two-stroke oil: 1 part oil + 50 parts oil. The quality of the fuel mixture decisively influences gasoline.
  • Page 17 6.1.5 Filling the machine with fuel CAUTION The maximum permissible speed of the disc or blade must be at least as high as the maximum speed printed on the machine.Accessories driven at a speed above their maximum permissible speed may break and fly apart.
  • Page 18 Remove the spray jets from the guard. 6.3 Adjusting the guard Slacken the three clamping nuts on the forward section of the saw arm approx. one complete turn. Release the tension on the drive belt by turning the belt tensioning cam counterclockwise carefully as far as it will go (until resistance is felt, i.e.
  • Page 19: Operation

    NOTE DANGER Especially when using the machine in this configuration Before starting the engine, check that the saw is for the first time, check to ensure that the throttle cable is correctly secured to the saw carriage. correctly adjusted. When the throttle control is pressed Move the cutting depth adjustment lever into the fully, the machine must run up to maximum speed.
  • Page 20 WARNING DANGER After fitting a new cutting disc, the machine must be Guide the machine evenly and do not apply lateral allowed to run at full speed under no load for approx. pressure to the cutting disc. Always bring the machine 1 minute.
  • Page 21: Care And Maintenance

    8 Care and maintenance machine should stand upright and should not be laid on its side. Take care to ensure that no dust finds its way onto the underlying filter screen. NOTE Change the air filter if motor performance drops notice- WARNING ably or if the machine becomes difficult to start.
  • Page 22: Adjusting The Carburetor

    All other adjustments must Use the spark plug wrench to screw the spark plug be carried out at a Hilti service center. into the cylinder (12 Nm). Fit the ignition cable connector to the spark plug.
  • Page 23: Troubleshooting

    If necessary, the machine should be repaired Remove the spark plug. by Hilti Service. Pour a little two-stroke oil into the cylinder (1 to 2 teaspoons). 8.11 Checking the power tool after care and Pull the starter handle a few times.
  • Page 24 The disc specification is unsuitable Change the specification or request for the material to be cut. advice from Hilti. Drive belt or cutting disc slips. Check the drive belt tension and disc clamping parts and eliminate the fault.
  • Page 25: Disposal

    10 Disposal Most of the materials from which Hilti machines or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back old machines and appliances for recycling. Ask Hilti customer service or your Hilti representative for further information.
  • Page 26: Ec Declaration Of Conformity (Original)

    For repair or replacement, send the tool or related parts This constitutes Hilti’s entire obligation with regard to immediately upon discovery of the defect to the address warranty and supersedes all prior or contemporaneous of the local Hilti marketing organization provided.
  • Page 27 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3503 | 0712 | 00-Pos. 1 | 1 Printed in Italy © 2012 Right of technical and programme changes reserved S. E. & O 288290 / A2 Printed: 07.07.2013 | Doc-Nr: PUB / 5128401 / 000 / 00...

Table of Contents