OPTEX FA CD33 SERIES Instruction Manual

Displacement Sensor
CD33 SERIES
CD33-30□□
CD33-50□□
INSTRUCTION MANUAL
● Confirm if the item meets your needs.
● Before the use, you should first thoroughly read this
manual and operate correctly as mentioned.
● You should keep this manual at hand for proper use.
Carefully read and understand the safety precautions before operation. The
important information is provided to protect your health and property. Do
not apply any other installing or operating procedure other than that
Meanings of Safety Symbol
Indicates a possible hazard that may result in death,
serious injury, WARNINGS or serious property damage
WARNING
if the product is used without observing the stated
instructions.
WARNING
● The light source of this product applies the visible light semiconductor
laser. Do not allow the laser beam to enter an eye, either directly or
reflected from reflective object. If the laser beam enters an eye, it may
cause blindness.
● Do not disassemble or modify the product since it is not designed to
automatically stop the laser emission when open. Disassembling or
modifying at customer's end it may cause personal injury, fire or electric
shock.
● This product is not an explosion proof construction. Do not use the
product under flammable , explosive gas or liquid environment.
● Use of controls or adjustments or performance of procedures other
WARNING Safety Precautions
● It is dangerous to wire or attach/remove the connector with the power
on. Make sure to turn off the power before operation.
●Installing in the following places may result in malfunction:
1. A dusty or steamy place
2. A place generating corrosive gas
3. A place directly receiving scattering water or oil.
4. A place suffered from heavy vibration or impact.
●The product is not designed for outdoor use.
●Do not use the sensor in a transient state at power on（Approx. 15min.
Warm up period）
●Do not wire with the high voltage cable or the power lines.
Failure to do this will cause malfunction by induction or damage.
●Do not use the product in water.
●Operate within the rated range.
● Wipe off dirt on the emitting/receiving parts to maintain correct
detection. Also, avoid direct impact on the product.
●This product cannot be used as a safety device to
protect human body.
Precautions for using laser
■Laser label
This product is classified as Class 2 (Ⅱ) Laser Product by JIS
C6802/IEC/FDA Laser Safety Standard.
●Regulations in the USA
When exporting laser devices to the USA, the USA laser control, FDA
(Food and Drug Administration) is applied. This product has been already
reported to CDRH (Center for Devices and Radiological Health). For
details, contact our customer service.
Label-A
Label-A
Ramco Innovations
Laser type
CD33-120□□
CD33-250□□
Mandatory Requirements
Label-B Analog ground wire is not equipped for connector type. Therefore connect the analog
ground terminal of analog input equipment and the 0V terminal of power supply.
MF (multi functional) input activates when connected to GND(-) for NPN type,
and when connected to (+) for PNP type.
Label-C
1) Connect the lead wires correctly. The analog output wire must not be in contact
with any other wire. Do not turn on the power while wiring.
2) The blue wire（0V） and shield wire（analog GND） are internally connected.
Use the blue wire（0V） for the power supply and use the shield wire（analog GND） for
analog output.
Label-B Label-C
800-280-6933
Connection diagram
NPN type
(Analogue/Voltage/Dual)
PNP type
(Analogue/Voltage/Dual)
NPN type (RS422)
PNP type (RS422)
Pins configuration
Caution for connection
MF (multi functional ) input
Specifications
●Specifications of Measuring Range
① CD33-30N(P)
②
CD33-30N(P)A
Cable type
③ CD33-30N(P)V
④ CD33-30N(P)-422 CD33-
Type
① CD33-30CN(P)
② CD33-30CN(P)A
Connector type
③ CD33-30CN(P)V
④
CD33-30CN(P)-422 CD33-5
Center
30mm
Measuring ｒange ±4mm
Light source
Peak power
IEC/JIS
Laser Class
FDA
Near
Spot size 0.15×0.15mm
(approx.
Middle 0.1×0.1mm
volume)
Far
*1 0.15×0.15mm
±0.1% F.S.
Linearity *2
(F.S.=8mm)
2μm
Resolution *3
(Fast：4μm)
Fast
Response
Standard
time
High resolution
Sampling period
Temperature Drift
Distance Indicator
Indicators
Output Indicator
MF (multi functional) input
Circuit protection
Protection Category
Operating temp./humidity
Storage temp./humidity
Ambient Light
Vibration resistance
Shock resistance
Warm up period
Material
Cable type
Weight
Connector type
●Specifications of Output
Dual output
Type
CD33- ①
Supply Voltage
Current Consumption
55mA max. (DC24V)
Control output NPN/PNP Open colle
Q1
Control output
Outputs
Q2
Analog output
Interface
φ5 5core 2m
Cable type *4
cable(PVC) AWG24
Connection
Connector type
*1 Defined with center strength 1/e2(13.5％ ). There may
The sensor may be damaged when there is a highly reflec
*2 Averaging: 64(High resolution), Sampling period:500μs
*3 Middle of measuring range, Object: white ceramic.
*4 Diameter of min bend cable is 40mm.
Installation
Install the sensor and adjust the light spot onto the meas
the middle of measuring range.
Use M4 screw (tightening torque need to be under 0.8N･m
Distance indicator
shows orange when
object exists in the middle of
measuring range
Middle of
measuring
range
・Adjust the sensor position so that it is set parallel to th
・If there is any foreign object around the spot that is glos
measurement.
www.optex-ramco.com
CD33-
CD33-
CD33-
CD33-
CD33-
CD33-
±
0.6
0.5
0.4×
±0
(F.S
(Fa
avera
avera
avera
5
Laser off、
-10～
-20～
Sun light
10 to
A
CD
DC12～24V
(+10%/-5%)
85mA
includin
(Residual vo
NPN/PNP O
(R
－ 4～
φ5 6
8.2