Technical Data - Metabo TKHS 315 M Operating Instructions Manual

ENGLISH
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body or workpiece):
– replace saw blade (see section 'Ca-
re and Maintenance').
Saw dust build-up
No dust collector or dust collector of in-
sufficient capacity connected (see
"Dust collector" in chapter "Operation"):
– connect dust collector, or
– open sliding plate, or
– increase suction capacity.

16. Technical Data

Voltage
Nominal current
Fuse protection min.
Protection class
Motor speed
Motor power
Power input P
1
Power output P
2
Saw blade cutting speed approx.
Riving knife thickness
Saw blade
saw blade diameter (outer)
saw blade hole (inside)
cutting width
max. base body thickness of the saw
blade
Cutting depth
Saw blade vertical
at 45° saw blade tilt
Dimensions
Saw table length
Saw table width
Table extension length
Table extension width
Height (saw table)
Height (overall)
38
Height adjustment mechanism of
saw blade working stiff
Spindle of height adjustment mecha-
nism gummy:
– clean spindle and spray with Care
and Maintenance Spray (see chap-
ter "Care and maintenance").
Bevel tilt adjustment working stiff
Wing nut or retaining nut on on the op-
posite side of the chip case tightened to
much:
– slightly loosen wing nut or retaining
nut.
TKHS 315 M TKHS 315 M
2.5 WNB 3.1 WNB
230 V 230 V
1~50 Hz 1~50 Hz
A 10.9 13.4
A 1 x 16 1 x 16
(time-lag) (time-lag)
IP 54 IP 54
-1
min 2750 2800
kW 2.5 kW S6 3.1 kW S6
40% 40%
kW 1.72 kW S6 2.2 kW S6
40% 40%
m/s 47 47
mm 2,5 2,5
mm 315 315
mm 30 30
mm 2,6 2,6
> >
mm 2,3 2,3
≤ ≤
mm 0 - 85 0 - 85
mm 0 - 53 0 - 53
mm 800 800
mm 600 600
mm 794 794
mm 510 510
mm 850 850
mm 1000 1000
Motor carrier unit tilts independently
If the motor carrier unit tilts indepen-
dently when setting the bevel tilt, the re-
taining nut on the opposite side of the
chip case is not tightened enough:
– adjust retaining nut as required.
TKHS 315 M TKHS 315 M
3.4 DNB 4.2 DNB
400 V 400 V
3~50 Hz 3~50 Hz
5.8 7.5
3 x 10 3 x 16
(time-lag) (time-lag)
IP 54 IP 54
2700 2800
3.4 kW S6 4.2 kW S6
40% 40%
2.5 kW S6 3.0 kW S6
40% 40%
47 47
2,5 2,5
315 315
30 30
2,6 2,6
> >
2,3 2,3
≤ ≤
0 - 85 0 - 85
0 - 53 0 - 53
800 800
600 600
794 794
510 510
850 850
1000 1000
TKHS 315 M TKHS 315 M
2.5 WNB Saudi Arabia
110 V 230 V
1~50 Hz 1~60 Hz
23 11.0
– 1 x 16
(time-lag)
IP 54 IP 54
2750 3350
2.5 kW S6 2.5 KW S6
40% 40%
1.6 kW S6 1.82 KW S6
40% 40%
47 56
2,5 2,5
315 315
30 30
2,6 2,6
> >
2,3 2,3
≤ ≤
0 - 85 0 - 85
0 - 53 0 - 53
800 800
600 600
794 794
510 510
850 850
1000 1000