Table of Contents
Advertisement
0017_33_1v5IVZ.fm
TKHS 315 M
Originalbetriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Origineel gebruikaanwijzing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
www.metabo.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Metabo TKHS 315 M
Summary of Contents for Metabo TKHS 315 M
- Page 1 0017_33_1v5IVZ.fm TKHS 315 M Originalbetriebsanleitung ......... . 3 Original operating instructions .
-
Page 2: Scope Of Delivery
I_0014en4A.fm 5.2.16 Original operating instructions ENGLISH Scope of delivery 1 Plate, table rear extension 10 Accessory storage (2x) 20 Guide bar for mitre fence 2 Blade guard 11 Transport handle (2x) 21 Support (2x) 3 Suction hose 12 Leg (4x) 22 Mounting bracket (2x) 4 Fence carrier, lower 13 Stanchion, short (2x) -
Page 3: Machine Overview
ENGLISH Machine overview 24 Table extension 29 Crank for cutting height setting, 34 Motor carrier unit – angle of incli- stepless from 0 – 85 mm nation steplessly adjustable from 25 Suction hose 0° through 47° 30 ON/OFF switch 26 Blade guard 35 Wheel set 31 Transport handles 27 Rip fence... -
Page 4: Table Of Contents
ENGLISH – Keep all documents supplied with Table of Contents Safety Instructions this machine for future reference. Retain proof of purchase in case of warranty claims. Specified conditions of Scope of delivery ....22 – This device must not be sold or lent Machine overview .... - Page 5 ENGLISH Wedges may only be cut using a stance to driven components when are doing so, the saw blade must be wedge cutting jig, adapted to the operating the device. at a complete standstill. desired wedge thickness, length, Wait for the saw blade to come to a ...
-
Page 6: Symbols On The Machine
ENGLISH 4. Clear the blockage using a suitable Safety devices Hazard caused by modificati- tool. on of the machine or use of parts not Riving knife tested and approved by the manuf- Symbols on the machine The riving knife (51) prevents the work- acturer! piece from being caught by the rising Strictly follow these instructions... -
Page 7: Special Product Features
ENGLISH Handle for push block switch. Both switch versions are illu- Crank for cutting height adjustment strated below. The handle for the push block (56) is The cutting height is adjusted by tur- screwed to a matching board (55). It is ning the crank (63). -
Page 8: Assembly
ENGLISH For use as rip fence the long fence Only if you follow the instructions exact- extrusion (67) must be installed. It is ly does the saw conform to the safety mounted on the guide extrusion at regulations and can be safely operated. the front of the saw table. -
Page 9: Flange Nut M8
ENGLISH Note: The blade guard is tilted slightly down- The switch buttons must point to the right-hand side. ward on the operator side after installa- tion on the riving knife. Caution! Make sure the cable does not run over sharp edges and is not bent. 6. -
Page 10: Screw On The Flange Nuts
ENGLISH – from the inside screw on flange Adjusting the rip fence nuts (91) – do not yet tighten ful- 1. Slide rip fence (107) on the guide rail and lock with the lock lever 2. Mounting the guide bar (89): Insert (106). - Page 11 ENGLISH 2. Attach each of the supports (119) with one bearing bolt (120), one washer (117) and one flange nut (118) to the table extension (see il- lustration). Tightening the screwed connections 4. Tighten flange nuts. Check all screwed connections of ...
-
Page 12: Mains Connection
ENGLISH The transport handles are installed on Mains connection the wiring of the outlet must be the front legs of the saw. changed by a qualified electrician: (125) 1. To each transport handle fit a 1. After the saw and all of its safety Danger! High voltage (126) hexagon head screw... -
Page 13: Dust Collector
ENGLISH – blade guard; and tractor when working in enclosed 1. Remove blade guard and table in- spaces. sert. – feeding aids (push stick, push block and handle). 2. Dismount the saw blade (see “Saw blade change” in chapter “Care and Use personal protection equipment: The dust collector must comply with maintenance”). -
Page 14: Setting The Saw Blade Tilt
ENGLISH Setting the saw blade tilt 2. The rip fence (141) is set from the top on the guide extrusion (142) at the front of the saw. Danger! 3. Set the rip fence to the cutting Parts of the body or objects in the width. -
Page 15: Tips And Tricks
ENGLISH 3. Turn the flat head screw (143) of used, parts can be ejected due to Tips and Tricks the table insert extrusion (144) centrifugal force in an explosive- clockwise by 1/4 turn and remove type manner. the table insert. Before making a cut: make a trial Do not use: ... -
Page 16: Aligning The Riving Knife
ENGLISH Distance to the saw blade: 1. Fit table insert extrusion (156) flush into the saw table. – The distance between the saw bla- de's outer edge and the riving knife shall be between 3 and 8 mm. – The riving knife must project over the saw table at least as far as the saw blade does. -
Page 17: Storing The Saw
MDF, composite materials K Saw blade HW 315 x 2.8 x 30 Contact your local Metabo representati- 84 alternate top bevel teeth ve if you have Metabo power tools re-... -
Page 18: Technical Data
– open sliding plate, or – slightly loosen wing nut or retaining – increase suction capacity. nut. 16. Technical Data TKHS 315 M TKHS 315 M TKHS 315 M TKHS 315 M TKHS 315 M TKHS 315 M 2.5 WNB 3.1 WNB... - Page 19 ENGLISH TKHS 315 M TKHS 315 M TKHS 315 M TKHS 315 M TKHS 315 M TKHS 315 M 2.5 WNB 3.1 WNB 3.4 DNB 4.2 DNB 2.5 WNB Saudi Arabia Weight complete approx. Guaranteed sound power level according to DIN EN 1870-1 (2007)*...
- Page 20 091 005 8967 091 001 4030 091 003 1260 091 101 8691 628 100 628 101 628 056 628 015 628 016 628 057 628 058 091 005 3353 Metabowerke GmbH Metabo-Allee 1 72622 Nuertingen Germany www.metabo.com...
Need help?
Do you have a question about the TKHS 315 M and is the answer not in the manual?
Questions and answers