Pentair Pentek Series Electronic Manual page 39

SECTION 7: Hitachi
7.4 Motor Specifications
Materials of Construction
PARTS MATERIALS
Housing Baked epoxy-coated gray iron
Fasteners Stainless steel
Shaft Splined or keyed stainless steel
Rotor Double epoxy-coated
Thrust Bearings Kingsbury-type 420 stainless steel
Mechanical Seal Nitrile rubber (NBR), grease packed
Diaphragm Nitrile rubber
Sand Slinger Baked epoxy-coated gray iron
Lead Wire (or Cable) Double-insulated, heat and water-resistant,
167°F/75°C, 600V
Motor
diAMeter hP KW
8* 50 37
8* 60 45
8 7.5 5.5
8 10 7.5
8 15 11
8 20 15
8 25 18.5
8 30 22
8 40 30
8 50 37
8 60 45
8 75 55
8 100 75
8 125 90
8 150 110
10 40 30
10 50 37
10 60 45
10 75 55
10 100 75
10 125 90
10 200 150
10 250 185
12 150 110
12 200 150
12 300 225
14 250 185
14 300 225
*Motor is 8" diameter, but constructed to operate with a 6" liquid end.
Hitachi is a registered trademark of Hitachi Industrial Equipment Systems Co., Ltd.
®
38
6" and Larger Submersible Motors
®
Volts Ph hZ rPM
460 3 60 3600
460 3 60 3600
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 3600
460 3 60 3600
460 3 60 3600
460 3 60 3600
460 3 60 3600
460 3 60 3600
460 3 60 3600
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 1800
460 3 60 3600
460 3 60 3600
460 3 60 1800
460 3 60 1800
460 3 60 3600
460 3 60 1800
460 3 60 1800
shAFt
cAtAlog leNgth eXteNsioN
NuMBer (l) (l1)
86hit2-50-4 45.28 2.875
86hit2-60-4 48.03 2.875
8hit4-7-4 32.4 4
8hit4-10-4 32.4 4
8hit4-15-4 41.34 4
8hit4-20-4 41.34 4
8hit4-25-4 44.09 4
8hit4-30-4 44.09 4
8hit2-40-4 44.09 4
8hit2-50-4 46.44 4
8hit2-60-4 49.19 4
8hit2-75-4 53.15 4
8hit2-100-4 53.8 4
8hit2-125-4 66.14 4
8hit2-150-4 70.08 4
10hit4-40-4 49.21 4
10hit4-50-4 49.21 4
10hit4-60-4 59.84 4
10hit4-75-4 59.84 4
10hit4-100-4 69.68 5
10hit4-125-4 69.68 5
10hit2-200-4 69.68 5
10hit2-250-4 79.53 5
12hit4-150-4 56.3 5
12hit4-200-4 68.11 5
12hit2-300-4 78.75 5
14hit4-250-4 68.31 5
14hit4-300-4 76.18 5
** 8" motors with 6" flange when using stainless steel bolts have
a thrust rating of 5,000 lbs. A thrust value of 10,000 lbs. can be
obtained using grade-8 heat-treated stainless steel bolts.
l1
l
d
diAMeter thrust
(d) cAPAcity Weight
5.5 10,000 **5,000 157
5.5 10,000 **5,000 182
7.52 10,000 298
7.52 10,000 298
7.52 10,000 320
7.52 10,000 320
7.52 10,000 342
7.52 10,000 342
7.52 10,000 320
7.52 10,000 353
7.52 10,000 408
7.52 10,000 463
7.52 10,000 518
7.52 10,000 595
7.52 10,000 661
8.52 10,000 507
8.52 10,000 507
8.52 10,000 639
8.52 10,000 639
8.52 10,000 794
8.52 10,000 794
8.52 10,000 816
8.52 10,000 948
10.53 10,000 959
10.53 10,000 1235
10.53 10,000 1455
12.6 10,000 1698
12.6 10,000 1940