Motor Dimensions - Pentair Pentek Series Electronic Manual

SECTION 7: Hitachi
7.4 Motor Specifications
Materials of Construction
PARTS MATERIALS
Motor Sleeve Stainless steel construction
Castings Baked epoxy-coated gray iron
Fasteners Stainless steel
Shaft NEMA splined stainless steel
Flange NEMA standard type
Rotor Double epoxy-coated
Thrust Bearings Kingsbury-type 420 stainless steel
Mechanical Seal Nitrile rubber (NBR), grease packed
Diaphragm Nitrile rubber
Sand Cap Polyurethane
Sand Slinger Stainless steel
Lead Wire (or Cable) Double-insulated, heat and water-resistant,
167°F/75°C, 600V
diAMeter hP KW Volts Ph
6 5 3.7 200 3
6 5 3.7 230 1
6 5 3.7 230 3
6 5 3.7 460 3
6 7.5 5.5 200 3
6 7.5 5.5 230 1
6 7.5 5.5 230 3
6 7.5 5.5 460 3
6 10 7.5 200 3
6 10 7.5 230 1
6 10 7.5 230 3
6 10 7.5 460 3
6 15 11 200 3
6 15 11 230 1
6 15 11 230 3
6 15 11 460 3
6 20 15 200 3
6 20 15 230 3
6 20 15 460 3
6 25 18.5 200 3
6 25 18.5 230 3
6 25 18.5 460 3
6 30 22 200 3
6 30 22 230 3
6 30 22 460 3
6 40 30 460 3
8 50 37 460 3
8 60 45 460 3
*Models are 8" motors with 6" pump connection.
Hitachi Control Boxes
ype 1 NEMA Enclosure
T
In-Panel Circuit Breaker
Magnetic Contactor
Terminal Blocks for External Controls
UL Recognized
Hitachi is a registered trademark of Hitachi Industrial Equipment Systems Co., Ltd.
®
6" and Larger Submersible Motors
®
WiNgiNg
cAtAlog serVice resistANce
hZ NuMBer FActor (ohMs)
60 6hit2-5-8 1.15
r-y, B-y, r-B, 2.172,
60 6hit2-5-1 1.15
0.512, 2.627
60 6hit2-5-2 1.15 0.806
60 6hit2-5-4 1.15 3.05
60 6hit2-7-8 1.15
r-y, B-y, r-B, 1.401,
60 6hit2-7-1 1.15
0.400, 1.774
60 6hit2-7-2 1.15 0.651
60 6hit2-7-4 1.15 2.43
60 6hit2-10-8 1.15
r-y, B-y, r-B, 1.052,
60 6hit2-10-1 1.15
0.316, 1.310
60 6hit2-10-2 1.15 0.448
60 6hit2-10-4 1.15 1.619
60 6hit2-15-8 1.15
r-y, B-y, r-B, 0.678,
60 6hit2-15-1 1.15
0.230, 0.850
60 6hit2-15-2 1.15 0.312
60 6hit2-15-4 1.15 1.074
60 6hit2-20-8 1.15
60 6hit2-20-2 1.15 0.258
60 6hit2-20-4 1.15 0.861
60 6hit2-25-8 1.15
60 6hit2-25-2 1.15 0.21
60 6hit2-25-4 1.15 0.666
60 6hit2-30-8 1.15
60 6hit2-30-2 1.15 0.166
60 6hit2-30-4 1.15 0.554
60 6hit2-40-4 1.15 0.358
60 86hit2-50-4* 1.15 0.331
60 86hit2-60-4* 1.15 0.278

Motor Dimensions

d
rAted serVice shAFt
iNPut FActor eXteNsioN
AMPs iNPut AMPs (l1)
17.5 19.5 2.87"
24 27.5 2.87"
15 17 2.87"
7.5 8.5 2.87"
25.4 28.5 2.87"
36 41 2.87"
22 26 2.87"
11 13 2.87"
33.3 37.2 2.87"
50 58 2.87"
29 33 2.87"
14.5 16.5 2.87"
47.4 53.5 2.87"
72 85 2.87"
42 46 2.87"
21 23 2.87"
61.2 69.5 2.87"
54 60 2.87"
27 30 2.87"
77.3 87.5 2.87"
68 76 2.87"
34 38 2.87"
91.8 104 2.87"
82 94 2.87"
41 47 2.87"
56 61 2.87"
65 73 2.87"
80 90 2.87"
hP KW Ph
5 3.7 1
7.5 5.5 1
10 7.5 1
15 11 1
l1
l
leNgth diAMeter thrust
(l2) (d) cAPAcity Weight
22.95" 5.5" 3,500 95
26.97" 5.5" 3,500 110
22.95" 5.5" 3,500 95
22.95" 5.5" 3,500 95
24.80" 5.5" 3,500 99
29.92" 5.5" 3,500 128
24.80" 5.5" 3,500 99
24.80" 5.5" 3,500 99
26.97" 5.5" 3,500 110
29.92" 5.5" 3,500 128
26.97" 5.5" 3,500 110
26.97" 5.5" 3,500 110
29.92" 5.5" 3,500 128
33.46" 5.5" 3,500 148
29.92" 5.5" 3,500 128
29.92" 5.5" 3,500 128
31.5" 5.5" 3,500 137
31.5" 5.5" 3,500 137
31.5" 5.5" 3,500 137
36.22" 5.5" 3,500 161
36.22" 5.5" 3,500 161
36.22" 5.5" 3,500 161
38.19" 5.5" 3,500 176
39.19" 5.5" 3,500 176
38.19" 5.5" 3,500 176
40.55" 5.5" 5,000 187
45.28" 7.52" 5,000 353
48.03" 7.52" 5,000 408
Volts cAtAlog NuMBer
230 hit-5cBd
230 hit-7.5cBd
230 hit-10cBd
230 hit-15cBd
37