The information contained in this manual is subject GeneRal safetY to change by Canadian Solar Inc. without prior notice. Canadian Solar Inc. gives no warranty of any · All modules must be installed by licensed kind whatsoever, either explicitly or implicitly, electricians in accordance to the applicable with respect to the information contained herein.
| 7 damage the module mechanically or electrically. · Modules can be wired in series to increase voltage oPtImum oRIentatIon anD tIlt or in parallel to increase current. To connect modules · To maximize your annual yield, find out the in series, connect the cables from the positive optimum orientation and tilt for PV modules terminal of one module to the negative terminal...
690.8(D)). relevant hardware should be made of stainless steel, unless otherwise specified. CaBle anD ConneCtoR PRoteCtIon · Canadian Solar Inc. does not provide grounding hardware. · Secure the cables to the mounting system using UV-resistant cable ties. Protect exposed cables ·...
BoltInG · This mounting method has been qualified by Canadian Solar Inc. as well as certified by VDE. and CSA. · Modules should be bolted to supporting structures through the mounting holes in the rear frame flanges only.
5400 Pa Compatible module types: CS3L-P Notice: when the modules need to be installed in heavy snow area, please inform Canadian Solar Inc.’s technical support department in writing for advices. Failure to follow this notice may violate the warranty. · To protect against electric shock or injury, electrical...
Page 14
INSTALLATION MANUAL ANNEX OF STANDARD SOLAR MODULES For professional use only...
Page 15
INSTALLATION MANUAL DISCLAIMER The information contained in this manual is subject to change by Canadian Solar Inc. without prior notice. Canadian Solar Inc. gives no warranty of any kind whatsoever, either explicitly or implicitly, with respect to the information contained herein.
Page 16
· Canadian Solar Inc.’s warranty may be void in cases where improper clamps or unsuitable installation The loads described in this manual corresponds to test loads. For installations complying with IEC methods are found.
Page 18
| 5 Use four clamps on the short side and two clamps Use four clamps on the long side. Mounting rails on the long side. An additional support bar should run parallel to the long side frame. be placed below the center of the module. A1 range = (410 –...
Page 20
≤ Downforce load 5400 Pa Notice: when the modules need to be installed in heavy snow area, please inform Canadian Solar Notice: this method is recommended for better Inc.’s technical support department in writing for reliability. advices. Failure to follow this notice may violate the warranty.
Page 22
| 9 CS1k-MS Use four clamps on the long side. Mounting rails Use four clamps on the long side. Mounting rails run parallel to the long side frame. run perpendicularly to the long side frame. A1 range = (0 – 239) mm Maximum Load: Uplift load ≤...
Page 24
| 11 CS6v-p, CS6v-M and CS6v-MS Use four clamps on the long side. Mounting rails Use four clamps on the short side. Mounting rails run perpendicularly to the long side frame. run parallel to the long side frame. A1 range = (0 – 239) mm Maximum Load: ≤...
Page 26
| 13 Use four clamps on the short side and two clamps Use four clamps on the short side. on the long side. An additional support bar should be placed below the center of the module. A2 range = (0 – 210) mm A2 range = (170 –...
Page 27
Do not touch the front glass or cast shadow onto it. · The mounting method has been qualified by Canadian Solar Inc. as well as certified by VDE and Do not damage the surface of the frame. Ensure that the insertion profiles overlap the CSA.
Page 28
| 15 CS3k-p, CS3k-MS, CS6k-p, CS6k-M, CS6k-MS, CS6v-p, CS6v-M and CS6v-MS Use two insertion profiles running parallel to the long Use two insertion profiles running perpendicularly to side frame. the long side frame. Maximum Load: Maximum Load: Uplift load ≤ 2400 Pa Uplift load ≤...
Page 30
≤ 5400 Pa MOUNTINg METhOD C: MOUNTINg METhODS wITh (SINgLE-AXIS TRACkER) · Canadian Solar Inc. modules can be mounted on single-axis trackers using center clamps or mounting Mounting Rail holes as described below. All the requirements of the standard module installation manual and specific tracker detailed installation instructions should apply.
Page 34
| 21 Open Short Maximum Operating Operating Max. Series Overall Circuit Circuit weight Module Type power voltage current Fuse Dimension voltage Current <kg> pmax <w> vmp <v> Imp <A> Rating <A> <mm> voc <v> Isc <A> CS6v-255MS 27.2 9.38 33.3 9.91 15.00 CS6vh-115MS...
Page 36
| 23 Open Short Maximum Operating Operating Max. Series Overall Circuit Circuit weight Module Type power voltage current Fuse Dimension voltage Current <kg> pmax <w> vmp <v> Imp <A> Rating <A> <mm> voc <v> Isc <A> CS3U-390MS 40.4 9.66 48.2 10.17 CS3U-395MS 40.6...
Page 38
SAFETy wARNINg · Canadian Solar Inc. recommends to avoid rotating brush cleaning methods, as they could create · Cleaning activities create risk of damaging the micro-cracks in the PV modules.
Page 39
· Rev A10 was amended and released in April 11 , 2018. · Rev A11 was amended and released in April 20 , 2018. · Rev A12 was amended and released in July , 2018. CANADIAN SOLAR INC. 545 Speedvale Avenue West, Guelph, Ontario, Canada N1K 1E6 www.canadiansolar.com...