Use And Limitations - eXact PipeCut 360 System User Manual

Hide thumbs Also See for PipeCut 360 System:
Table of Contents

Advertisement

Safety
Extension cables outside
When you work outdoors, always use an extension
cable that is made and approved for outdoor use.
Be alert
Concentrate on your work. Use common sense. Do
not use the pipe saw when you are tired or drowsy.
Never use the pipe saw under the influence of alcohol
or drugs.
Use the right tool
Never use a low-power tool or accessory for work
that requires a high-powered tool. Never use the
pipe saw for purposes for which it is not intended.
Remove the key
Check that the blade key has been removed before
starting the pipe saw.
Accessories
Only use additional accessories and equipment
recommended by the manufacturer. The use of
another manufacturers accessories may cause an
accident.
Check for damaged parts
Before using the pipe saw, check that: all of its
components are in good condition, are correctly
installed and that all moving parts operate correctly.
Always check the attachments of the blade guard.
Also check that everything else that can affect
operation is in good condition. Never use the pipe
saw if the power switch does not operate properly
or if the cable is damaged. A damaged part should
be repaired or replaced with a new one at an approved
service agency.
Have your machine repaired at an approved
service agency
Your retailer will give you a list of approved service
agencies. For safety reasons, only approved service
agencies may service or change the machine's
electrical components.
Do not cut pipes containing asbestos
Asbestos is considered to be carcinogenic substance.
Check the blade
Use only correct blades in good condition, which are
suitable for the material to be cut, for the pipe size
and for the speed of the saw
Intended use and limitations
The Exact PipeCut 360 pipe saw is intended for use
as a pipe fitter's tool at the installation site. The Exact
PipeCut 200 pipe saw can only be used to cut round
pipes, with a diameter of 75 to 360 mm and a
maximum wall thickness of 8mm with steel and 12mm
with plastics. The Exact PipeCut 360 pipe saw can
be used to cut all normal pipe materials, such as
steel, stainless steel, cast iron, copper, aluminum,
and plastic. Exact PipeCut 360 pipe saw is intended
for short, intermittent use. The machine may be
loaded for 2.5 minutes during a 10-minute period
(S3 25 %). The Exact PipeCut 360 pipe saw is not
intended for use in industrial production.
The pipe saw must never be used in the following
cases, if:
-There is water or another liquid, explosive gases or
poisonous chemicals inside the pipe to be cut.
-The power switch is faulty.
-The power cable is faulty,
-The blade is bent.
-The blade is blunt or in poor condition.
-The plastic components are cracked or have parts
missing.
-The gripper unit is not properly tightened around
the pipe or if it is warped.
-The blade guard cover or moving blade guard has
been damaged or removed from the machine.
-The locking mechanisms do not work properly
(UNLOCK-button).
-The pipe saw has become wet.
When using the pipe saw, the following factors
must always be taken into consideration:
-Ensure that the pipe to be cut is empty.
-Ensure that the blade is correctly installed.
-Ensure that the diameter and thickness of the blade
are suitable for the pipe saw and that the blade is
suitable for the rpm-range of the machine.
-Never use sideways force to stop the blade, always
allow the blade to stop freely.
-Check the attachments of the blade guards.
-Never use excessive force when using the pipe saw.
-Never use the pipe saw to lift the pipe while it is still
attached to the pipe.
-Avoid overloading the electric motor.
-Always follow the safety and operating instructions
and current regulations.
6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PipeCut 360 System and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents