Table of Contents
Advertisement
Quick Links
SBC220 -- 2-Bay Networked Charger
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor
dance with the manufacturer's instructions.
8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other appara
tus (including amplifiers) that produce heat. Do not place any open flame sources on the product.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been dam
aged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vas
es, on the apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing
connection.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
1/14
Advertisement
Table of Contents
Related Manuals for Shure SBC220
Summary of Contents for Shure SBC220
- Page 1 SBC220 -- 2-Bay Networked Charger IMPORTANT SAFETY INSTRUCTIONS 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor...
- Page 2 • Do not short circuit; may cause burns or catch fire • Do not charge or use battery packs other than Shure rechargeable batteries • Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.
-
Page 3: General Description
• P10R (legacy) • P9RA (legacy) Note: P3RA and P9HW universal bodypacks are also compabible with SBC220, but must to be powered on, with the “Auto Off” feature disabled for successful charging and monitoring. UR5 universal bodypacks are not compati... -
Page 4: Controls And Connectors
Shure Incorporated Controls and Connectors ① Power LED • White = Batteries are charging • Red = Charger is in storage mode ② Reset Button Press and hold to restore charger factory settings, including network settings. ③ Storage Mode Button Press and hold to activate storage mode, which charges or discharges batteries to the optimal voltage for long- term storage. -
Page 5: Power Save Mode
Shure Incorporated ⑧ Ethernet Link Speed LED (Amber) • Off = 10 Mbps • On = 100 Mbps ⑨ Ethernet Status LED (Green) • Off = No network link • On = Network link established • Flashing = Network link active ⑩... -
Page 6: Adding A Charger
Shure Incorporated Adding a Charger To save space and reduce clutter, a combination of up to 4 SBC220 and SBC240 chargers can share 1 power supply and Ethernet connection. 1. Unplug charger from the power source. 2. Remove the rubber covers from the charger connectors between chargers to be ganged. -
Page 7: Led Indicators
Shure Incorporated Charging To charge, place batteries and transmitters into the charging bays as shown, with the LCD facing the charging LEDs. The LEDs illuminate to indicate battery status. Warning: Do not insert transmitters using AA batteries. LED Indicators Color... -
Page 8: Storage Mode
2. Check the temperature. If the battery temperature is above 60°C or below 0°C, the error LED flashes. 3. Contact Shure service. Battery may be discharged beyond re covery or have internal problems. Replace battery. • Error LED amber steady on 4 charg... -
Page 9: Restoring Factory Settings
If you have multiple devices to manage, connect each device to a router or network switch. The Ethernet port LEDs on your device will illuminate to indicate network connectivity. Verify that Shure devices can see each other by looking for the network connectivity icon on the front panel (location varies). -
Page 10: Configuration Tips
• Check your firewall settings to make sure Wireless Workbench has access to your network • Use multiple Ethernet switches to extend the network for larger installations For more help, visit the Help menu in Wireless Workbench or http://www.shure.com/wwb (http://www.shure.com/ wwb). -
Page 11: Connecting To An External Control System
IP mode and IP address, view the MAC address, and view firmware version. Connecting to an External Control System The SBC220 networked charger connects to external control systems such as AMX or Crestron via the Ethernet. For a comprehensive list of command strings, visit pubs.shure.com/ (http://pubs.shure.com/guide/SBC220). -
Page 12: Model Variations
Korea SBC220-K Taiwan SBC220-TW Australia SBC220-AZ India SBC220-IN Global SBC220 (no power supply) Specifications SBC220 Compatible Batteries Up to 2 SB900/SB900A Compatible Transmitters Up to 2 ULXD1, ULXD2, QLXD1, QLXD2, AD1 or AD2 Charge Current 0.75 A maximum Charge Time 1 hour = 50% charged;... - Page 13 DHCP or Manual IP address Certifications Meets essential requirements of all applicable European Directives. Eligible for CE marking. The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance Authorized European representative: Shure Europe GmbH Headquarters Europe, Middle East & Africa Department: EMEA Approval Jakob-Dieffenbacher-Str.
- Page 14 Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.