1. Manuals
  2. Brands
  3. Trek Manuals
  4. Bicycle
  5. Domane SLR 2020
  6. Service manual

Trek Domane SLR 2020 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

2020 DOMANE SLR/SL
SERVICE MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Domane SLR 2020 and is the answer not in the manual?

Questions and answers

Related Manuals for Trek Domane SLR 2020

Summary of Contents for Trek Domane SLR 2020

  • Page 1 2020 DOMANE SLR/SL SERVICE MANUAL...

  • Page 2: Table Of Contents

    2020 Domane Service Manual Table of Contents 1. Install common components A. Install and adjust the seatpost B. Install the front derailleur C. Install the rear derailleur D. Install the chain keeper 2. Route and install brakes A. Install rear brake in frame B.

  • Page 3: Install Common Components

    Install common components INSTALL COMMON COMPONENTS A. Install and adjust the seatpost C. Install the rear derailleur Tighten the bolt just until the seatpost and To adjust the seat height, loosen the seatpost wedge are snug. Do not fully tighten yet. clamp bolt, adjust the height, and re-tighten TOOLS AND MATERIALS REQUIRED Install the rear derailleur on the the rear...

  • Page 4: Route And Install Brakes

    ROUTE AND INSTALL BRAKES ROUTE CABLES AND HOUSINGS THROUGH THE FRAME A. Install rear brake in frame B. Install front brake and brake hose Route rear derailleur housing A. Mechanical Route front derailleur housing Please see the figure at the bottom of page 5 Place lower bearing on the fork race.

  • Page 5: The Down Tube Window Frame

    Route cables and housings through the frame Route cables and housings through the frame B. Di2 Put the grommet around the derailleur housing While holding the housing and hose at the Tighten the bolts to 1.2Nm. and insert the grommet into the bottom of the head tube, move the guide down the downtube Route the front derailleur cable drive side dropout.

  • Page 6: Route Battery And Install

    Route cables and housings through the frame Route cables and housings through the frame Route the rear derailleur cable from the hole in Route the battery wire in through the storage From the bottom of the down tube, use two Install the storage cover with the lever pointing the driveside chainstay to the bottom bracket hole and out the bottom bracket hole.

  • Page 7: Install The Fork

    Route cables and housings through the frame INSTALL THE FORK Install the fork Route the Park Tool wire from the right bar Plug the two wires into the bar end plug. Install the brow cover. Flex the sides of the end through the handlebar and out the left bar brow cover outward, and position it over the With lower bearing installed on the fork, slide...

  • Page 8: Route And Install The Stem And Handlebar

    There are different cabler wranglers for different stems depending on Blendr compatibility. (PNs: 582439, 584649, 587846). VIEW FROM BELOW NOTE Trek recommends using the cable wrangler on stems 100mm and longer. For stems shorter than 100mm, the cable wrangler does not provide any additional benefit.

  • Page 9: Domane Torque Specifications

    Route and install the stem and handlebar DOMANE TORQUE SPECIFICATIONS Place the shift levers on the handlebar to the Component Torque value desired location. Chain keeper bolt Down tube window frame bolt 1.2Nm Battery holder bolts 0.3Nm Cable guide to frame bolts Rear Isospeed frame screw Top tube cable guide bolt Damper assembly bolts...

  • Page 10: Service Information

    SERVICE INFORMATION APPENDIX A. Install the front Isospeed From inside the decoupler, insert a screw into Di2 handlebar specifications for reference the driveside bore hole so the screw points to Apply grease to the bore holes, as well as the the outside of the head tube.
  • Page 11 Install the front Isospeed Install the front IsoSpeed Hand thread the elliptical nut a few turns to Place one hand on the opposite side of the To fully tighten, apply good pressure while Lower the pre-load spacer into the decoupler the LEFT to secure it for the next step.

  • Page 12: Install The Rear Isospeed

    Install the rear IsoSpeed Install the rear IsoSpeed B. Install the rear IsoSpeed Clean the surface with Install the bolt and washer in the forward end alcohol or similar of the decoupler and torque to spec on decal. BOLT HEAD Install the damper assembly in the seat tube.

  • Page 13: Assemble And Install The Dt Storage Door

    Assemble and install the DT storage door 2020 Domane Service Manual Assemble and install the DT storage door C. Assemble and install the From the inside, put the wave spring over the Press the pin through so it’s flush with the If equipped with a Bontrager multi-tool, push DT storage door lever shaft.

  • Page 14: Install The T47 Bottom Bracket

    Grease the threads on the bottom bracket. • 4mm hex head wrench, extended arm, round head • Loctite Blue 242 Trek recommends using Bontrager fenders. Domane SL, SLR, and LT models Remove the set screw or plastic plug from under the fork crown.

  • Page 15: Rear Fender Chart

    2020 Domane Service Manual Install fenders Rear fender chart Frame Size Part Number Description Domane SL Domane SLR Domane+ LT Domane+ HP 575637 56 – 62 56 – 62 56 – 62 Center mount facing down 575637 47 – 54 52 –...

This manual is also suitable for:

Domane sl 2020

Table of Contents

Save PDF