Summary of Contents for ETC Echoflex Elaho Inspire Station
Page 1
Elaho Inspire Stations Programming Guide Echo Protocol Version 3.1 Part Number: 8186M1220-3.1.0 Rev.A Released: 2018-09...
Page 2
® ® and Inspire are registered trademarks of Electronic Theatre Controls, Inc. in the United States and other countries. All other trademarks, both marked and not marked, are the property of their respective owners. Echoflex intends this document, whether printed or electronic, to be provided in its entirety.
Table of Contents Introduction Document Conventions Help from Technical Services Overview Station Configuration Record/Program Mode Function switch Rotary and DIP Switches Function switch: Preset Preset Toggle Use Off Preset Mode Raise / Lower Sequence Control Function switch: Custom With ElahoAccess Without ElahoAccess Function switch: Zone Zone Selection Zone Toggle...
Page 4
Function Switch for Space Combine Function switch: Preset Function switch: Zone Station Functionality 1-Button Station Factory Defaults Preset Zone Custom 2-Button Station Factory Defaults Preset Zone Custom 4-Button Station Factory Defaults Preset Zone Custom Space Combine in Preset Space Combine in Zone Space Combine in Custom 4-Button with Fader Station Factory Defaults...
Page 5
Remove Wall Plate Install Wall Plate Install Button Legends Rotary Switch Assignments DIP Switch Settings 4-Button with Fader Station Color Mode DIP Switch Settings Table of Contents...
Introduction ® Welcome to the Elaho Inspire Station Programming Guide. This document will guide you in the programming and configuration of your Elaho Inspire Stations, including the 1-button, 2-button, 4-button, 6-button, 8-button, and the 4-button with fader station. This guide is intended for use after station installation; therefore the content of this document is targeted at programming the configuration and features of the station only.
Help from Technical Services If you are having difficulties, your most convenient resources are the references given in this document. To search more widely, try the Echoflex website at echoflexsolutions.com. If none of these resources are sufficient, contact Echoflex Technical Services directly at one of the offices identified below.
Overview Elaho Inspire stations provide preset, zone, space combine, and color controls for use with Elahocontrol systems only. Reference Station Functionality on page 14 for detailed information about each station type and its possible function settings, or download the Inspire Station data sheet located on the Echoflex website echoflexsolutions.com for the complete listing including model and ordering...
Station Configuration The Elaho Inspire Station has on-board switch and button settings that are available from the front of the station when it is installed and the cover is removed. Record/Program Mode The [RECORD/PROGRAM MODE] button provides access to RECORD/ PROGRAM record and program settings.
Use Off “Use Off” functionality enables the last button on the station with a dedicated space off action. A single push of the “Off” button will set the level of all zones to zero using a 2 second • fade time. A double push of the “Off”...
Without ElahoAccess By default the Custom Function switch setting on an Elaho Inspire Station provides behavior that extends the Zone Function switch setting behaviors for control of more Zones. For example, on an 8 button station, Zone control mode defaults to zones 1 through 6. Setting the station in Custom control mode, by default, provides access to zones 7 through 12.
Zone Raise / Lower Raise and lower the selected zone level using the assigned raise and lower station controls. Each station type has configured raise and lower controls. Reference Station Functionality on page 14 for the station type you are configuring for complete details. Zone Raise / Lower from a Button With a Zone Selected The selected zone button LED lights blue to indicate its active state.
Color Control Mode (4 button with fader station only) Color Control functionality allows the Inspire 4 button with fader station to control patched LED zones on an Elaho DMX Scene Controller. To enable Color Control on a 4 button with fader station: DIP Switch First, set DIP switches 5 and 6 according to the desired color mode.
Page 14
12 o'clock position (50%) toward the 6 o'clock (100%) position. Studio Mode Select Studio mode provides access to raise and lower intensity, color temp, and tint for ETC LED fixtures that support Studio mode using the fader knob for the selected zone.
Record/Program Mode Program mode allows adjustment of the consecutive range of presets and zones assigned to the station by allowing you to set the starting preset or zone, respectively. Enter Program mode by pressing and holding the [Record / Program mode] button for three seconds. The Function switch determines whether edits are made to the consecutive range of presets or zones.
Program Zone Start Set the Function switch to its lowest position of Zone. Press and hold the [Record / Program mode] button for three seconds to enter Program mode. The “Mode” LED illuminates (steady amber) and the first zone control button LED flashes the current (first) zone controlled.
Space Combine (4-button only) Placing the 4-button station (model # E1004) in space combine mode, accomplished by setting DIP switch 3 On, allows for combined control of multiple spaces. For more information on DIP switch settings, DIP Switch Settings on page 40 In space combine mode, the zones with the same number but in different spaces will respond identically when the spaces are combined.
Program Mode for Space Combine Program mode behaves in a slightly different manner when the 4-button station is set to space combine mode. Press and hold the [Record / Program mode]button for three seconds to enter Program mode. The “Mode” LED illuminates (steady amber) and the first space combine button LED flashes the current (first) space controlled.
Station Functionality This section provides detail for each stations function including its factory default settings, and each button default when the station function switch is set to Preset, Custom, and Zone. 1-Button Station on the next page • 2-Button Station on page 18 •...
1-Button Station The 1-button Elaho Inspire Station offers control of a single preset or zone as determined by the Function switch setting. Factory Defaults The 1-button Inspire Station ships from the factory in the following default settings: Rotary switches are set to Address 1, Space 1. Reference Rotary Switch •...
Zone The 1-button station supports the following button actions: Push Hold Double-tap Double-tap the button to toggle the zone to its full or off, using a 1/2 second fade time. Station Functionality...
Custom The 1-button station provides the following button actions by default before configuration using ElahoAccess: Push Hold Double-tap Double-tap the button to toggle the zone to its full or off, using a 1/2 second fade time. Note: These are the default button actions for the station when the Function switch is set to Custom.
2-Button Station The 2-button Inspire Station offers control of two presets or 1 zone as determined by the Function and DIP switch settings. Factory Defaults The 2-button Inspire Station ships from the factory in the following default settings: Rotary switches are set to Address 1, Space 1. Reference Rotary Switch •...
Zone The 2-button station supports the following button actions: Push Hold Double-tap Double-tap the button to toggle the zone to its extents using a 1/2 second fade time. Custom The 2-button station provides the following button actions by default before configuration using ElahoAccess: Push Hold...
Page 25
Double-tap Double-tap the button to toggle the zone to its extents using a 1/2 second fade time. Note: These are the default button actions for the station when the Function switch is set to Custom. For custom configuration using ElahoAccess, reference the ElahoAccess Mobile App integrated help system.
4-Button Station The 4-button Inspire Station offers control of four presets or two zones, or space combine actions for up to five consecutive spaces as determined by the Function and DIP switch settings. Factory Defaults The 4-button Inspire Station ships from the factory in the following default settings: Rotary Switch Rotary switches are set to Address 1, Space 1.
Zone The 4-button station supports the following button actions: Push Hold Double-tap Double-tap the button to toggle the zone to its extents using a 1/2 second fade time. With No Zone Selected When no zone is selected, the raise selection and lower selection buttons (1 and 4) change the intensity levels for the configured space.
Custom The 4-button station supports the following button actions by default before configuration using ElahoAccess: Push Hold Double-tap Double-tap the button to toggle the zone to its extents using a 1/2 second fade time. Note: These are the default button actions for the 4-button station when the Function switch is set to Custom.
Hold Note: Double-tap is not a supported feature in Space Combine mode. When the 4-button station in Space Combine mode, and the Function switch is set to Preset, the spaces will wrap, meaning the last button on the station will combine with the first space configured for control on the station.
Space Combine in Custom Setting the Function switch to Custom, with DIP switch 3 On, enables Space Combine mode on the 4-button station. The 4 button station in Space Combine mode supports the following button actions by default before configuration using ElahoAccess: Push Hold Note:...
4-Button with Fader Station The 4-button with fader Inspire Station offers control of up to five presets or four zones as determined by the Function and DIP switch settings. Factory Defaults The 4-button with fader Inspire Station ships from the factory in the following default settings: Rotary Switch Rotary switches are set to Address 1, Space 1.
Zone The 4-button with fader station supports the following button and fader actions: Push Hold Double-tap Double-tap the button or fader knob to toggle the zone or space using a 1/2 second fade time. *Push the fader knob to execute an Off command anytime presets or zones are On in the same space, otherwise the action toggles the space.
Zone with Color Control Enabled With the Function switch set to Zone, and with Color Control mode enabled by configuring DIP switches 5 and 6, the 4-button with fader station supports the following fader actions: HSI Color Mode Intensity Saturation Color Temp Mode Intensity Station Functionality...
Page 34
Color Temp Studio Mode Intensity Color Temp Tint With No Zone Selected When no zone is selected, rotate the fader knob to perform space wide commands, changing all zone levels for the configured space. Elaho Inspire Station Programming Guide...
Custom The 4-button with fader station supports the following button and fader actions by default before configuration using ElahoAccess: Push Hold Double-tap Double-tap the button or fader knob to toggle the zone or space using a 1/2 second fade time. *Push the fader knob to execute an Off command anytime presets or zones are On in the same space, otherwise the action toggles the space.
6-Button Station The 6-button Inspire Station offers control of up to six presets or four zones as determined by the Function and DIP switch settings. Factory Defaults The 6-button Inspire Station ships from the factory in the following default settings: Rotary switches are set to Address 1, Space 1.
Zone The 6-button station supports the following button actions: Push Hold Double-tap Double-tap the button to toggle the selected zone or space using a 1/2 second fade time. With No Zone Selected When no zone is selected, the raise and lower buttons (1 and 6) perform a space raise and space lower, changing all zone levels for the configured space.
Custom The 6-button station supports the following button actions by default before configuration using ElahoAccess: Push Hold Double-tap Double-tap the button to toggle the selected zone or space using a 1/2 second fade time. Note: These are the default button actions for the station when the Function switch is set to Custom.
8-Button Station The 8-button Inspire Station offers control of up to eight presets or four zones as determined by the Function and DIP switch settings. Factory Defaults The 8-button Inspire station ships from the factory in the following default settings: Rotary switches are set to Address 1, Space 1.
Zone The 8-button station supports the following button actions: Push Hold Double-tap Double-tap the button to toggle the selected zone or space using a 1/2 second fade time. With No Zone Selected When no zone is selected, the raise and lower buttons (7 & 8) perform a space raise and space lower, changing all zone levels for the configured space.
Custom The 8-button station supports the following button actions by default before configuration using ElahoAccess: Push Hold Double-tap Double-tap the button to toggle the selected zone or space using a 1/2 second fade time. Note: These are the default button actions for the station when the Function switch is set to Custom.
Station Miscellaneous This section provides information pertaining to the mechanical features of the Inspire Stations including the following: Remove or Install the Wall Plate on the facing page • Install Button Legends on page 39 • Rotary Switch Assignments on page 40 •...
Remove or Install the Wall Plate Remove Wall Plate After station installation is complete, to gain further access to the Record/Program Mode Function switch features and set station , you must first remove the station wall plate. The wall plate is secured to the station with magnets that are attached to the wall plate. Using your index finger and thumb, lift the left and right side edges of the bottom of the wall plate, disengaging the magnets.
Install Button Legends Inspire Stations ship with standard button legends installed beneath a clear lens. An additional sheet of standard button legends are provided for field installation as needed. Note: Customize and print your own button legends on standard transparency. Download the button legend template provided on the Echoflex website at echoflexsolutions.com.
Rotary Switch Assignments Two rotary switches on the rear panel of the station provide for station address and space assignment. Each station must be set to a unique station address for the assigned space. By default, these switches are set to station Address 1, Space 1. Events and commands are shared by all devices within an assigned space.
4-Button with Fader Station Color Mode DIP Switch Settings DIP switches 5 and 6 on the 4-button with fader station set Color Mode functionality for the fader knob when the station is also set to Zone control mode: MODE DIP 5 DIP 6 Push action Rotate action...
Need help?
Do you have a question about the Echoflex Elaho Inspire Station and is the answer not in the manual?
Questions and answers