Subscribe to Our Youtube Channel
Related Manuals for Palmgren 84261A
Summary of Contents for Palmgren 84261A
- Page 1 & parts list 84261A ″ BENCH TOP JOINTER/PLANER Read carefully and follow all safety rules and operating instructions before first use of this product. 25164.09-0207...
-
Page 2: Specifications
Palmgren Operating Manual & Parts List 84261A SPECIFICATIONS DESCRIPTION ″ Table Size ..........28 ″... - Page 3 Palmgren Operating Manual & Parts List 84261A SAFETY RULES (CONTINUED) Fence Sliding Handle Fence Support TOOL SHOULD BE MAINTAINED Spacer • Always unplug tool prior to inspection. • Consult manual for specific maintaining and adjusting procedures. • Keep tool lubricated and clean for safest operation.
-
Page 4: Installation
Refer to Figure 5. ″ 11″ The Palmgren Half Bag Dust Collection Set is designed to provide ″ diameter dust dust collection for woodworking tools with a 2 exhaust port. The filter bag attachs to a 30-gallon trash can or a 30- gallon x 1.3 mil plastic trash bag for easy, convenient sawdust dis-... -
Page 5: Extension Cords
Palmgren Operating Manual & Parts List 84261A INSTALLATION (CONTINUED) MOTOR • Do not remove or alter grounding prong in any manner. In the Jointer/planer is supplied with a 1 HP motor. event of a malfunction or breakdown, grounding provides a The 120 Volt AC universal motor has the following specifications: path of least resistance for electrical shock. -
Page 6: Depth Of Cut
Palmgren Operating Manual & Parts List 84261A OPERATION (CONTINUED) Outfeed Max Depth • Do not plug in jointer/planer unless switch is in OFF position. Table ″ of Cut After turning switch on, allow jointer/planer to come to full speed before operating. -
Page 7: Adjusting Blade Height
Palmgren Operating Manual & Parts List 84261A • Rotate the cutterhead by hand. The blades should just touch OPERATION (CONTINUED) the straightedge. If a blade is too low or too high at either end, CAUTION: If the blade guard fails to operate properly, the spring adjust blade height using the jack screws. - Page 8 Palmgren Operating Manual & Parts List 84261A • Position the push-blocks flat on top of workpiece and push the OPERATION (CONTINUED) • Keep fingers close together. workpiece down against the table. • Use a hand-over-hand motion to maintain control over the •...
-
Page 9: Maintenance
Palmgren Operating Manual & Parts List 84261A • Loosen and remove three blade lock screws securing blade and MAINTENANCE blade clamp. • Lift blade and blade clamp from cutterhead. WARNING: Turn the switch to OFF position and unplug • Clean any sawdust and resin buildup from cutterhead and jointer/planer from power source before proceeding to do blade clamp. -
Page 10: General Maintenance
Palmgren Operating Manual & Parts List 84261A • Keep blades sharp (see “Sharpening Blades” , page 9). Sometimes MAINTENANCE (CONTINUED) • Remove four bolts (Ref. No. 24) that retain motor mounting replacing blades is less expensive than resurfacing them. Keeping a spare set of blades on hand is recommended. Blades plate (Ref. -
Page 11: Troubleshooting
Palmgren Operating Manual & Parts List 84261A TROUBLESHOOTING SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Defective switch Motor does not start 1. Have switch replaced 2. Defective motor 2. Have motor replaced/repaired NOTE: 1 and 2 must be done by a qualified service technician 3. - Page 12 Palmgren Operating Manual & Parts List 84261A Figure 24 – Replacement Parts Illustration for Fence and Infeed Table...
- Page 13 Palmgren Operating Manual & Parts List 84261A REPLACEMENT PARTS LIST FOR FENCE AND INFEED TABLE Ref. Ref. Description Part No. Qty. Description Part No. Qty. Fence 18963.09 Table Pin 18424.00 5-0.8mm Hex Nut Frame Pin 18425.00 6-1.0mm Hex Nut Fence Support 25143.00...
- Page 14 Palmgren Operating Manual & Parts List 84261A Figure 25 – Replacement Parts Illustration for Base...
- Page 15 Palmgren Operating Manual & Parts List 84261A REPLACEMENT PARTS LIST FOR BASE Ref. Ref. Description Part No. Qty. Description Part No. Qty. Base with Outfeed Table Fan Pulley 18445.00 6201ZZ Ball Bearing 00520.00 Fan Belt 18444.00 3AMI-12 Retaining Ring 00519.00 -20 x ’’...
-
Page 16: Two Year Limited Warranty
This warranty gives you specific legal rights and you may also have other legal rights which may vary from state to state. Responsibility of Original Purchaser (Initial User): • To process warranty claim on this product, DO NOT return it to the retailer. The product must be evaluated by Palmgren. Call (800) 621-6145 for instructions.
Need help?
Do you have a question about the 84261A and is the answer not in the manual?
Questions and answers